Axis P1354 - Manuals

Axis P1354 – Manual in PDF format online.

Manuals:

Manual

Manual Axis P1354

Summary

Page 3 - Support

This product fulfills the requirements for immunityaccording to EN 55024 office and commercial environments Australia/New Zealand This digital equipment fulfills the requirements for RFemission according to the Class B limit of AS/NZS CISPR 22.The product shall be connected using a shielded networkc...

Page 5 - Hazard Levels; DANGER; Other Message Levels; IS

AXIS P13 Series Safety Information Read through this Installation Guide carefully before installing the product. Keep the InstallationGuide for future reference. Hazard Levels DANGER Indicates a hazardous situation which, if not avoided, will result indeath or serious injury. WARNING Indicates a haz...

Page 6 - WARNING; Transportation

AXIS P13 Series Safety Instructions WARNING • The Axis product shall be installed by a trained professional. NO NO NOTICE TICE TICE • The Axis product shall be used in compliance with local laws and regulations. • To use the Axis product outdoors, or in similar environments, it shall be installed in...

Page 7 - AXIS P13 Series

AXIS P13 Series WARNING • Risk of explosion if the battery is incorrectly replaced. • Replace only with an identical battery or a battery which is recommended by Axis. • Dispose of used batteries according to local regulations or the battery manufacturer's instructions. 7 E N G L IS H

Page 9 - Installation Steps

AXIS P13 Series Installation Guide This Installation Guide provides instructions for installing AXIS P1354/P1357 Network Cameraon your network. For other aspects of using the product, see the User Manual available at www.axis.com Installation Steps 1. Make sure the package contents, tools and other ...

Page 10 - Hardware Overview

AXIS P13 Series Hardware Overview 1 4 5 6 7 8 9 10 11 12 13 14 3 2 1 Focus puller 2 Zoom puller 3 LED indicator 4 Power LED 5 Network LED 6 Control button 7 I/O terminal block 8 Iris connector 9 Power connector* 10 RS485/42211 SD card slot (microSD) 12 Audio in13 Audio out14 Network connector PoE * ...

Page 11 - LED Indicators

AXIS P13 Series LED Indicators Note • The Status LED can be configured to be unlit during normal operation. To configure, go to Setup > System Options > Ports & Devices > LED . See the online help for more information. • The Status LED can be configured to flash while an event is active...

Page 12 - Connectors and Buttons; Network Connector; Digital output

AXIS P13 Series Connectors and Buttons For specifications and operating conditions, see page 13 . Network Connector RJ45 Ethernet connector with Power over Ethernet (PoE). NO NO NOTICE TICE TICE The product shall be connected using a shielded network cable (STP). All cables connectingthe product to ...

Page 13 - SD Card Slot; Unmount; Specifications; Operating Conditions; Products

AXIS P13 Series RS485/RS422 Connector Two terminal blocks for RS485/RS422 serial interface used to control auxiliary equipment such aspan-tilt devices. SD Card Slot NO NO NOTICE TICE TICE • Risk of damage to SD card. Do not use sharp tools or excessive force when inserting or removing the SD card. •...

Page 14 - Power Consumption; Power Connector

AXIS P13 Series Power Consumption Products DC PoE AXIS P1354 8-28 V DC max 7.2 WIEEE 802.3af/802.3at Type 1 Class 3 AXIS P1357 8-28 V DC max 7.9 WIEEE 802.3af/802.3at Type 1 Class 3 Connectors I/O Connector 4–pin terminal block For an example diagram, see Connection Diagrams on page 16 . Function Pi...

Page 15 - Audio Connector; Audio Input; Audio Output; Function

AXIS P13 Series Audio Connector 3.5 mm audioconnectors (stereo) 1 2 3 1 Tip 2 Ring 3 Sleeve Audio Input Microphone/Line in Ground Audio Output Line out (mono) Ground RS485/422 Connector Two 2-pin terminal blocks for RS485/RS422 serialinterface. The serial port can be configured to support: • Two-wir...

Page 16 - Connection Diagrams; Install the Hardware; Connect the Cables

AXIS P13 Series Connection Diagrams I/O Connector 1 2 3 4 1 0 V DC (-) 2 DC output 3.3 V, max 50 mA 3 Digital input 0 to max 40 V DC 4 Digital output 0 to max 40 V DC, open drain, 100 mA Install the Hardware Connect the Cables 1. Connect external input/output devices if required, such as alarm devic...

Page 17 - Access the Product; Adjust Focus

AXIS P13 Series - Connect an external power adapter to the power connector block. For wiringinformation, see page 14 . 5. Check that the indicator LEDs indicate the correct conditions, see LED Indicators on page 11 . Access the Product AXIS IP Utility and AXIS Camera Management are recommended metho...

Page 18 - Fine-tune focus automatically; Focus Assistant

AXIS P13 Series 7. On the Focus page, click Fine-tune focus automatically and wait until automatic fine tuning is completed. 8. Click Enable iris . If the button is inactive the iris is already enabled. 9. If needed, make further adjustments under the Advanced tab. See the online help for more infor...

Page 19 - Reset to Factory Default Settings; Setup; Further Information

AXIS P13 Series Reset to Factory Default Settings Important Reset to factory default should be used with caution. A reset to factory default will resetall settings, including the IP address, to the factory default values. Note The installation and management software tools are available from the sup...