Axis P1354 - Manual

AXIS P13 Series WARNING • Risk of explosion if the battery is incorrectly replaced. • Replace only with an identical battery or a battery which is recommended by Axis. • Dispose of used batteries according to local regulations or the battery manufacturer's instructions. 7 E N G L IS H

AXIS P13 Series Installation Guide This Installation Guide provides instructions for installing AXIS P1354/P1357 Network Cameraon your network. For other aspects of using the product, see the User Manual available at www.axis.com Installation Steps 1. Make sure the package contents, tools and other ...

AXIS P13 Series Hardware Overview 1 4 5 6 7 8 9 10 11 12 13 14 3 2 1 Focus puller 2 Zoom puller 3 LED indicator 4 Power LED 5 Network LED 6 Control button 7 I/O terminal block 8 Iris connector 9 Power connector* 10 RS485/42211 SD card slot (microSD) 12 Audio in13 Audio out14 Network connector PoE * ...

AXIS P13 Series LED Indicators Note • The Status LED can be configured to be unlit during normal operation. To configure, go to Setup > System Options > Ports & Devices > LED . See the online help for more information. • The Status LED can be configured to flash while an event is active...

AXIS P13 Series Connectors and Buttons For specifications and operating conditions, see page 13 . Network Connector RJ45 Ethernet connector with Power over Ethernet (PoE). NO NO NOTICE TICE TICE The product shall be connected using a shielded network cable (STP). All cables connectingthe product to ...

AXIS P13 Series RS485/RS422 Connector Two terminal blocks for RS485/RS422 serial interface used to control auxiliary equipment such aspan-tilt devices. SD Card Slot NO NO NOTICE TICE TICE • Risk of damage to SD card. Do not use sharp tools or excessive force when inserting or removing the SD card. •...

AXIS P13 Series Power Consumption Products DC PoE AXIS P1354 8-28 V DC max 7.2 WIEEE 802.3af/802.3at Type 1 Class 3 AXIS P1357 8-28 V DC max 7.9 WIEEE 802.3af/802.3at Type 1 Class 3 Connectors I/O Connector 4–pin terminal block For an example diagram, see Connection Diagrams on page 16 . Function Pi...

AXIS P13 Series Audio Connector 3.5 mm audioconnectors (stereo) 1 2 3 1 Tip 2 Ring 3 Sleeve Audio Input Microphone/Line in Ground Audio Output Line out (mono) Ground RS485/422 Connector Two 2-pin terminal blocks for RS485/RS422 serialinterface. The serial port can be configured to support: • Two-wir...

AXIS P13 Series Connection Diagrams I/O Connector 1 2 3 4 1 0 V DC (-) 2 DC output 3.3 V, max 50 mA 3 Digital input 0 to max 40 V DC 4 Digital output 0 to max 40 V DC, open drain, 100 mA Install the Hardware Connect the Cables 1. Connect external input/output devices if required, such as alarm devic...

AXIS P13 Series - Connect an external power adapter to the power connector block. For wiringinformation, see page 14 . 5. Check that the indicator LEDs indicate the correct conditions, see LED Indicators on page 11 . Access the Product AXIS IP Utility and AXIS Camera Management are recommended metho...

AXIS P13 Series 7. On the Focus page, click Fine-tune focus automatically and wait until automatic fine tuning is completed. 8. Click Enable iris . If the button is inactive the iris is already enabled. 9. If needed, make further adjustments under the Advanced tab. See the online help for more infor...

AXIS P13 Series Reset to Factory Default Settings Important Reset to factory default should be used with caution. A reset to factory default will resetall settings, including the IP address, to the factory default values. Note The installation and management software tools are available from the sup...