Autostart AS-1412 - Manuals

Page 3 - only when the Hood is up.; Always solder and tape all connections.

AS-1412 Installation Guide P. 3 Before You Get Started … Ƈ On vehicles with a manual Transmission, always ensure that all Doors will get the Unit out of Ready Mode. Switch the wire used so that it is triggered by all Doors. Ƈ Make sure that the Parking Brake and Door Switch contacts work properly. Ƈ...

Page 4 - Harness Description; -Pin Main Ignition Harness; IGNITION; DO NOT JUMP; DO NOT JUMP WIRES

P. 4 Installation Guide AS-1412 Harness Description When connecting the Module, it is important to make sure that the connector with the Ground wire is connected first, before making the 12-volt connections. Should the Unit be powered up before being grounded, there could be serious damage to intern...

Page 5 - -Pin Secondary Harness; Screws tend to get loose or rusted over time and can; ON; 2-Pin Accessories Harness; TRUNK; Note

AS-1412 Installation Guide P. 5 5-Pin Secondary Harness Wire Description 1 BLACK (–) Chassis ground input This wire must be connected to bare, unpainted metal (the Chassis or true Body ground). It is preferable to use a factory ground bolt rather than a self-tapping screw. Screws tend to get loose o...

Page 6 - Connects to Negative Trunk Pin.

P. 6 Installation Guide AS-1412 Note: The system also gives a Disarm pulse on this wire before remote start. 6 BLUE / WHITE (–) L.E.D. output 2 V L.E.D. 7 WHITE / ORANGE (–) Starter Kill (Armed output) The unit is equipped with a selectable passive- or active-arming Starter Kill circuit that will im...

Page 7 - WHITE; If multiple relays or modules are connected; GRAY; This pin is not used – leave empty.; YELLOW; If no Glow-plug wire is found on the vehicle, the Glow

AS-1412 Installation Guide P. 7 Ignition barrel). Option 4 (Smart Ignition Re-Lock): Connects to the Negative Door trigger Input. When the Ignition Lock Option or the Lock Only Option is enabled: after the Brake Pedal is pressed and after a Door has been opened and closed, the Doors will RE-LOCK . 1...

Page 8 - Flashing the Hood Pin; Flash the Hood Pin; Remember

P. 8 Installation Guide AS-1412 12 YELLOW (+) Glow-plug input (Cont.) -plug input on the Module may be “timed out”. The Module will power up the Ignition and Glow-plug circuits and simply wait for the time-out before starting: Connecting the Glow-plug input wire of the Module to Ignition will hold t...

Page 9 - OFF; Table 1; How to Enter Programming Options Mode; Table 2; The Module can only be programmed Function by Function

The Programming Assistance Button (a.k.a. PAB.) The PAB is located on the side of the Module. Thispush button mimics theHood-Pin switch in order toavoid having to get out ofthe vehicle and pressing theHood-Pin switch. The PAB will work only when theHood is up. Before Programming a Transmitter The Tr...

Page 10 - Programming Options

P. 10 Installation Guide AS-1412 to re-enter all option selections for all functions of the Mode you are accessing. You may not skip Functions*. *NOTE: Pressing the Brakes at any given moment will save the selection(s) you have entered and will return you to the Programming Center. For each Function...

Page 11 - Auto Tach Programming Procedure; AutoTach; ONLY; Table 4; Multi-Speed Tach Programming; Table 5; Testing

AS-1412 Installation Guide P. 11 Auto Tach Programming Procedure NOTE: If no tach has been programmed and the ,, button is pressed, there will be no start attempt and the vehicle will give 5 flashes. If another Tach Programming is required, simply repeat the Auto Tach Programming Procedures. The Mod...

Page 14 - FLASH; Table 6; hot wire; To reset the Module:; Table 7; Troubleshooting Poor Transmitting Range

P. 14 Installation Guide AS-1412 1. FLASH the hood pin switch. 2. In ten seconds or less, press the Brake Pedal six times. 3. The Parking Lights will flash 8 times confirming the Reset. Table 6 On some vehicles, such as, BMW, and certain Volkswagens, etc., pressing the Brake pedal without the key in...