Autostart AS-1412 - Manual

Autostart AS-1412 – Manual, read for free online in PDF format. We hope this helps you resolve any issues you may have. If you have further questions, please contact us through the contact form.

Page 3 – only when the Hood is up.; Always solder and tape all connections.
Page 4 – Harness Description; -Pin Main Ignition Harness; IGNITION; DO NOT JUMP; DO NOT JUMP WIRES
Page 5 – -Pin Secondary Harness; Screws tend to get loose or rusted over time and can; ON; 2-Pin Accessories Harness; TRUNK; Note
Page 6 – Connects to Negative Trunk Pin.
Page 7 – WHITE; If multiple relays or modules are connected; GRAY; This pin is not used – leave empty.; YELLOW; If no Glow-plug wire is found on the vehicle, the Glow
Page 8 – Flashing the Hood Pin; Flash the Hood Pin; Remember
Page 9 – OFF; Table 1; How to Enter Programming Options Mode; Table 2; The Module can only be programmed Function by Function
Page 10 – Programming Options
Page 11 – Auto Tach Programming Procedure; AutoTach; ONLY; Table 4; Multi-Speed Tach Programming; Table 5; Testing
Page 14 – FLASH; Table 6; hot wire; To reset the Module:; Table 7; Troubleshooting Poor Transmitting Range

Loading the manual

Notice

The manufacturer will accept no responsibility for any electrical damage resulting from improper
installation of the product, be that either damage to the vehicle itself or to the Unit. This Unit must
be installed by a certified technician using all safety devices supplied. Please note that this guide
has been written for properly trained Autostart technicians, a certain level of skill and knowledge is
therefore assumed. Please review the Installation Guide carefully before beginning any work.

Warning

This Unit is designed for vehicles with an

automatic

Transmission only. Before installing the

Unit, test that the vehicle does not start when the gear select lever is in the “Drive” position. If it
starts in gear, install a manual-transmission car starter instead.

H.3.

0.S.3.20

DOC

.1.01

– September 2, 2003 – CA

Manufactured in Canada by Autostart

A U T O M A T I C

T R A N S M I S S I O N M U L T I -

C H A N N E L R E M O T E S T A R T E R S Y S T E M

AS-1412

Installation Guide

Table of Contents

Introduction ...................................................2
Included in the Package ...............................2

Before You Get

Started

… ........................3

Harness Description .....................................4

6-Pin Main Ignition Harness.....................4
5-Pin Secondary Harness ........................5
12-Pin Accessories Harness....................5

Flashing the Hood Pin ..................................8
The Programming Assistance Button (a.k.a.
PAB.) ............................................................9
Before Programming a Transmitter ..............9
How to Program the Transmitter. .................9
How to Enter Programming Options Mode...9
Programming Options.................................10
Auto Tach Programming Procedure ...........11
Multi-Speed Tach Programming .................11
Testing ........................................................11

Closing Up .................................................. 12
Supplementary Information ........................ 12
Fifth Relay Output (2nd Ignition or 2nd
Accessories or 2nd Crank Output) ............. 12

Ignition-controlled Door Locks ............... 13
Secure Lock........................................... 13
Passive or Active Arming Starter Kill ..... 13
Lock Pulse Duration .............................. 13
Engine Run Time ................................... 13
Idle Mode ............................................... 13

Resetting the Module (without the plug-in
valet) ........................................................... 13
Resetting the Module (with the use of the
plug-in valet) ............................................... 14
Troubleshooting Poor Transmitting Range 14

Please note:

Button

is for the

LOCK/UNLOCK

functions.

Button

is for the

START/STOP

functions.

Buttons

(together) is for the

TRUNK

release function.

The LED is NOT included in this model.

"Loading the manual" means you need to wait until the file loads and becomes available for online reading. Some manuals are very large, and the time they take to appear depends on your internet speed.

Summary

Page 3 - only when the Hood is up.; Always solder and tape all connections.

AS-1412 Installation Guide P. 3 Before You Get Started … Ƈ On vehicles with a manual Transmission, always ensure that all Doors will get the Unit out of Ready Mode. Switch the wire used so that it is triggered by all Doors. Ƈ Make sure that the Parking Brake and Door Switch contacts work properly. Ƈ...

Page 4 - Harness Description; -Pin Main Ignition Harness; IGNITION; DO NOT JUMP; DO NOT JUMP WIRES

P. 4 Installation Guide AS-1412 Harness Description When connecting the Module, it is important to make sure that the connector with the Ground wire is connected first, before making the 12-volt connections. Should the Unit be powered up before being grounded, there could be serious damage to intern...

Page 5 - -Pin Secondary Harness; Screws tend to get loose or rusted over time and can; ON; 2-Pin Accessories Harness; TRUNK; Note

AS-1412 Installation Guide P. 5 5-Pin Secondary Harness Wire Description 1 BLACK (–) Chassis ground input This wire must be connected to bare, unpainted metal (the Chassis or true Body ground). It is preferable to use a factory ground bolt rather than a self-tapping screw. Screws tend to get loose o...