Page 2 - Table of Contents; Introduction; section on page 15). The functions of the transmitter are as follows:
P. 2 User Guide Table of Contents Introduction ............................................................ 2 Using the Remote Control..................................... 2 Feature Confirmation Chart .................................. 3 Vehicle Status Request ..........................................
Page 3 - Feature Confirmation Chart
User Guide P. 3 Picture serves as example only. • Pressing and holding the LOCK button for more than 3 seconds will lock all doors and will send a constant pulse as long as the LOCK button is held down (maximum of 15 seconds). This constant pulse can be configured to activate certain functionalities...
Page 4 - Vehicle Status Request; To retrieve the vehicle status:; If the engine is NOT running
P. 4 User Guide Vehicle Status Request The status request feature allows the user to see the status of the vehicle i.e.: if the doors are locked or unlocked or if the vehicle is in cold weather mode, home valet mode, in valet mode or how much time is left in the run time cycle. The following chart...
Page 5 - User Guide; Status Request When the Engine is Running; When the vehicle’s doors are locked:; Table 2; When the vehicle’s doors are unlocked:; Table 3
User Guide P. 5 Status Request When the Engine is Running When the vehicle’s doors are locked: Run time Stage LED #1 LED #2 LED #3 LED #4 Beep(s) 1 st stage 3 flashes 3 If there is more than 3/4 of run time cycle 2 nd stage ON for 1 sec ON for 1 sec ON for 1 sec ON for 1 sec 1 st stage 3 flashes 3 I...
Page 6 - Alarm Status; Table 4; How Run Time Cycles Work; Table 5; Multi-Level Features; press the
P. 6 User Guide Alarm Status Status Stage LED #1 LED #2 LED #3 LED #4 Beep(s) Door If door is opened 1. flash 2. flash 1. flash 2. 1. flash 2. 1. flash 2. continuous Hood If hood is opened Flash Flash flash flash continuous Ignition If ignition is turned ON 1. flash 2. 1. flash 2. 1. flash 2. 1. fla...
Page 8 - customized feature 1; Remote Starting Your Vehicle; automatic transmission; Setting Your Vehicle into Ready Mode; manual transmission; To remote start your vehicle
P. 8 User Guide Note: When using the companion remote, Shift button must be pressed twice quickly the first time. For instance, to access customized feature 1 , press SHIFT twice quickly, SHIFT and SHIFT again followed by LOCK. Remote Starting Your Vehicle If your vehicle has an automatic transmissi...
Page 9 - Vehicle Presets; Heater & Heated Seats; Do not turn the key; Using the Remote Starter; Arming and Disarming the Security System; disarm; arm; Idle Mode
User Guide P. 9 Vehicle Presets Heater & Heated Seats When leaving the vehicle it is recommended to preset the accessory controls in preparation for the next remote start. Settings for the blower motor (fan) as well as heated seats (if equipped) should not be left on HIGH . It is recommended to ...
Page 10 - Turbo Mode
P. 10 User Guide To leave the vehicle in Idle Mode if your vehicle has an automatic transmission: 1. With the engine running, make sure to release the brake pedal and press the UNLOCK button (to unlock the doors, if installed) or the START/STOP button on the remote control until the parking lights c...
Page 11 - Valet Modes; Valet Mode Using the Valet Switch (if installed)
User Guide P. 11 4. Remove the key; the engine will continue running. 5. Exit the vehicle and close all doors, hood and trunk. 6. Press and hold either: a. LOCK to lock the doors and shut down the engine after 60 sec.; b. UNLOCK to unlock the doors and shut down the engine after 60 sec.; c. START/ST...
Page 12 - Panic Mode
P. 12 User Guide The LED will turn on solid. Getting out of valet mode • Hold the UNLOCK and START/STOP buttons simultaneously for 3 seconds. The parking lights will flash 2 times. The LED will turn off. Note : Once the remote valet is activated, the remote starter and alarm functions will be disabl...
Page 13 - enter; To; exit; Cold Weather Mode, do any one of the following actions:; Advanced Features: Installation-programmable Options; The installation-programmable options are as follows:; Passive or Active Arming; passive mode; Remote Door Locks
User Guide P. 13 minutes (or 8 or 20 minutes with diesel engines). Cold weather mode automatically ends after 24 hours (or 12 starts). To enter Cold Weather Mode: • Press the SHIFT button and then the START/STOP for 3 seconds . There will be two (2) beeps and the parking lights will flash three (3) ...
Page 15 - pressing and holding the; warning
User Guide P. 15 Home Valet If this feature is enabled, the user has the option of setting the vehicle to a no-remote-start mode. The alarm functions will still be active. Turbo Mode When left in turbo mode, the remote starter will keep the engine running for 60 seconds before shutting it down. This...
Page 16 - Siren or Horn Chirps; Disarmed Notification; Car Finder; Flashing LED; Troubleshooting Transmitting Range
P. 16 User Guide Siren or Horn Chirps ( ON by default.) The siren will chirp to confirm basic operations on the system: • By default, upon locking the doors the siren will give one chirp if all doors, hood or trunk are closed. • If a zone is open as the system is armed , the siren will give three ch...
Page 17 - Intrusion Codes through the LED Light; Diagnostics – Chirps Table; Chirps; Constant
User Guide P. 17 Intrusion Codes through the LED Light If there has been an intrusion in the vehicle while it was locked and armed, the LED will provide an intrusion code matching the type of the intrusion that took place. Disarm the alarm ( UNLOCK ) to identify the intrusion. The LED intrusion code...
Page 18 - Diagnostics – Parking Light Flash Table; Flashes
P. 18 User Guide Diagnostics – Parking Light Flash Table Flashes Description 1 • Doors locked, alarm and starter kill armed • Run time has expired • TRUNK button pressed • Start signal received by the module • Cold weather mode cancelled 2 • Remote start attempt cancelled by remote • Doors unlocked,...