Autostart AS-2272 - Manual

Autostart AS-2272

Autostart AS-2272 – Manual, read for free online in PDF format. We hope this helps you resolve any issues you may have. If you have further questions, please contact us through the contact form.

1 Page 1
2 Page 2
3 Page 3
4 Page 4
5 Page 5
6 Page 6
7 Page 7
8 Page 8
9 Page 9
10 Page 10
11 Page 11
12 Page 12
13 Page 13
14 Page 14
15 Page 15
16 Page 16
17 Page 17
18 Page 18
19 Page 19
20 Page 20
21 Page 21
22 Page 22
23 Page 23
24 Page 24
25 Page 25
26 Page 26
27 Page 27
28 Page 28
29 Page 29
30 Page 30
Page: / 30

Table of Contents:

  • Page 2 – Installation Guide; Table of Contents; Introduction
  • Page 5 – Installation Order
  • Page 7 – A basic introduction to the Relay; Why are Relays used?; then moved and makes contact with 87 (; either; 6, and then Ground the OTHER terminal to activate the relay. In
  • Page 11 – Harness Description
  • Page 12 – 2-pin Accessories Harness
  • Page 14 – Additional Ports; Entering Programming Mode
  • Page 15 – once; Manual or Automatic Transmission
  • Page 16 – Transmitter Programming Procedure; Programming Options
  • Page 17 – Virtual Tach System; Optional Time Delay Adjustment in Virtual Tach System; Follow these steps to program crank time adjustment, if needed:; Do not release the brake pedal.
  • Page 18 – once every time the; Multi-speed Tach Programming; Other Features of the Module
  • Page 19 – Clutch Bypass; With the pedal pressed:; OFF
  • Page 20 – Installation-programmable Features; Ignition-controlled Door Locks
  • Page 22 – Turbo Mode; Cold Weather Mode
  • Page 23 – enter; exit; Valet Mode; To put the system i n t o Valet Mode; To put the system o u t o f Valet Mode
  • Page 24 – twice; Panic Mode; manual transmission
  • Page 25 – Resetting the module to default features; To reset the module:; Closing Up; Remote-start the engine and listen for starter drag.
  • Page 26 – Door locks and trunk testing.; Troubleshooting Poor Transmitting Range
  • Page 27 – Diagnostics – Parking Light Flash Table
  • Page 28 – Troubleshooting Q & A
Loading the manual

Notice

The manufacturer will accept no responsibility for any electrical damage resulting from improper installation of the product, be that either
damage to the vehicle itself or to the unit. This unit must be installed by a certified technician using all safety devices supplied. Please
note that this guide has been written for properly trained Autostart technicians: a certain level of skills and knowledge is therefore
assumed. Please review the installation guide carefully before beginning any work.

Warning

Before installing the unit, if installing on a vehicle with a

manual

transmission, test that the OEM Door Switch contacts of the vehicle work

well, and that the Parking Brake system operates properly. If installing on a vehicle with an

automatic

transmission, test that the vehicle

does not start when the gearshift lever is in the “Drive” position. If it starts in gear, reset the remote starter to manual transmission.

DOC

.

1.00

- AS-2272 -

- July 7, 2008 -

- MO -

Made in China

M A N U A L / A U T O M A T I C

T R A N S M I S S I O N

M U L T I - C H A N N E L

R E M O T E S T A R T E R S Y S T E M






AS-2272




Installation Guide

"Loading the manual" means you need to wait until the file loads and becomes available for online reading. Some manuals are very large, and the time they take to appear depends on your internet speed.

Summary

Page 2 - Installation Guide; Table of Contents; Introduction

P. 2 Installation Guide Table of Contents Introduction ............................................................ 2 Included in the Kit .................................................. 3 Installation Tools.................................................... 3 Installation Points to Remember .......

Page 5 - Installation Order

Installation Guide P. 5 Installation Order The following is a suggested order for the Installation procedure. It is intended as a guide for novices, to help make the process of installing a remote starter module easier. Time is wasted by rewiring the module when mistakes are made. Also, the neatness...

Page 7 - A basic introduction to the Relay; Why are Relays used?; then moved and makes contact with 87 (; either; 6, and then Ground the OTHER terminal to activate the relay. In

Installation Guide P. 7 A basic introduction to the Relay What is a relay? A device that responds to a small current or voltage change by activating switches or other devices in an electric circuit. An electromagnetic switch, remote-controlled switch, a switching device. Why are Relays used? Relays ...

Other Autostart Models

All Autostart Other