AEG 35772G-M- Manuals

5 Description of the Hob Installation Fig. 1 Any gas installation must be carried out by a registered CORGI installer, and in accordance with existing rules and regulations. The relevant instructions are to be found in the second section of this manual.Please, ensure that, once the hob is installed,...

6 Burner minimum maximum diameter diameter Triple-crown (ultra-rapid) 160 mm 260 mm Large (rapid) 160 mm 240 mm Medium (semi-rapid) 120 mm 220 mm Small (auxiliary) 80 mm 160 mm As soon as a liquid starts boiling, turn down the flame so that it will barely keep the liquidsimmering. If you use a sauce...

7 Before any maintenance or cleaning can be carried out, you must DISCONNECT the hob from the electricity supply. The hob is best cleaned whilst it is still warm, as spillage can be removed more easilythan if it is left to cool. The Hob Top Regularly wipe over the hob top using a soft clothwell wrun...

8 Something Not Working? If the hob is not working correctly, please carry out the following checks before contacting your local AEG Service Force Centre. SYMPTOM There is no spark when lighting the gas The gas ring burns unevenly SOLUTION Check that the unit is plugged in and the electrical supply ...

10 Guarantee Conditions Standard guarantee conditions We, AEG, undertake that if within 12 months of the date of the purchase this AEG appliance or any partthereof is proved to be defective by reason only of faulty workmanship or materials, we will, at our discretionrepair or replace the same FREE O...

11 Instruction for the Installer Engineers technical data B U R N E R R A P I D SEMI-RAPID A U X I L I A R Y TRIPLE (large) ( m e d i u m ) (small) C R O W N POSITION M A X M I N M A X M I N M A X M I N MAX MIN NOMINAL THERMALPOWER (kW) 2.8 0.65 2.0 0.45 1.0 0.33 4.0 1.2 NOMINAL FLOWRATE (m 3 /h) 0....

12 Important safety requirements This hob must be installed in accordance with the Gas Safety (Installation and Use) Regulations(Current Edition) and the IEE Wiring Regulations (Current Edition). Detailed recommendationsare contained in the following British Standards Codes Of Practice: B.S. 6172/ B...

13 Installation Important This hob must be installed by qualified personnel to the relevant British Standards. Any gas installation must be carried out by a CORGI registered installer. The manufacturer will not accept liability, should the above instructions or any of the other safety instructions i...

14 560 150 min 48 0 FO 2038 Cut Out Size The dimensions of the cut-out are given in the diagram. Building In Building over a cupboard or drawer If the hob is to be installed above a cupboard or drawer it will be necessary to fit a heatresistant board below the base of the hob on the underside of the...

15 FO 2564 ON/OFF SWITCH FLEX OUTLET ON/OFF SWITCH FLEX OUTLET 1 FO 2563 2 Building over a kitchen unit with door Proper arrangements must be taken indesigning the furniture unit, in order to avoidany contact with the bottom of the hob whichcan be heated when it is operated. Therecommended solution ...

16 Fitting the Hob into the worktop Carry out the building in of the hob as follows: • p u t th e se al s supplied with the hob, onthe edges of the cut out:place them exactly on thefront and rear edge and at50 mm. from the sideedges, as shown in thediagram, taking care thatthe seals meet withoutover...

17 Electrical connections Any electrical work required to install this hob should be carried out by a qualified electrician or competent person, in accordance with the current regulations.THIS HOB MUST BE EARTHED. The manufacturer declines any liability should these safety measures not be observed.T...

19 Fault Finding Preliminary Electrical Systems Check START Isolate applianceand carry out: A: Earth Continuity check. Has inlet fuse blown? Carry out: C: Polarity check. Electricity supplyshould now besatisfactory. Carry out: D: Resistance to Earth check. Inlet wiringfaulty.Rectify anyfault. Isolat...

21 Check gas supply atburner Ignition System / Gas Ignition YES Check plug top fuse andreplace if necessary Check polarity and earthcontinuity of supply point Check earth continuityof appliance Ignitor does not spark Check fitting ofburners Check position of theelectrode Check by pass simmeradjusted...

22 Commissioning When the hob has been fully installed it will be necessary to checkthe minimum flame setting. To do this, follow the procedure below. - Turn the gas tap to the MAX position and ignite. - Set the gas tap to the MIN flame position then turn the control knob from MIN to MAX several tim...

23 Conversion from Natural Gas to LPG It is important to note that this model is designed for use with natural gas but can beconverted for use with butane or propane gas providing the correct injectors are fitted.The gas rate is adjusted to suit. Method • Ensure that the gas taps are in the 'OFF' po...