Adam Equipment CBW 45 - Manuals

3.0 INSTALLATION 3.1 LOCATING THE SCALE • The scales should not be placed in a location that will reduce the accuracy. • Avoid extremes of temperature. Do not place in direct sunlight or near air conditioning vents. • Avoid unsuitable tables. The table or floor must be rigid and not vibrate. • Avoid...

the level and the scale is supported by all four feet. • Attach the power supply cable to the connector on the bottom of the scale. Plug in the power supply module. The power switch is located on the base on the right side of the scale. • The scale will first display the model number (CBW 30- where ...

5.0 DISPLAYS The LCD display will show a value and a unit to the right of the digits. Other labels are TARE, GROSS, ZERO , / O (Stable) and (Low battery). 6.0 OPERATION 6.1 ZEROING THE DISPLAY • You can press the [Zero/Enter] key at any time to set the zero point from which all other weighing and co...

6.6.1 Setting up Check-weighing while weighing • Press [Limit] . It will show the current High Limit with the left most digit flashing and the HI symbol on the left of the display. • To select the digit to be changed press [Limit/ Î ] or [%/ Í ] . Use [Tare/ Ï ] to increment the flashing digit. When...

6.8 MANUAL ACCUMULATION • When the scale is set to manual accumulation the weight displayed will be stored in memory when the [Print] key is pressed and the weight is stable. • The display will show " ACC 1 " and then the total in memory for 2 seconds before returning to normal. The weight w...

6.9 AUTOMATIC ACCUMULATION • When the scale has been set to Automatic Accumulation the value is stored in memory automatically. • Add a weight to the scale. The beeper will sound when the scale is stable indicating the value is accepted. Remove the weight. • The display will show " ACC 1 " a...

CBWa Scales only: The CBWa scales can change units from kilograms to grams, pounds or pounds/ounces immediately if they are enabled as in the step above. This also allows the scales to be calibrated in either kilograms or pounds and all memory accumulations are in either kilograms or pounds as last ...

9.0 RS-232 INTERFACE The CBW scales comes with a bi-directional RS-232 interface. Specifications: RS-232 output of weighing data ASCII code 4800 Baud 8 data bits No Parity Connector: 9 pin d-subminiature socket Pin 3 Output Pin 2 Input Pin 5 Signal Ground Data Format for normal weighing operations, ...

C. When in parts counting mode, the weight, unit weight and count will be printed- GS 1.234 kg GS for Gross weight, NT for net weight and a unit of weight U.W. 12.34 g/pcs The average piece weight computed by the scale PCS 100 pcs The number of parts counted <lf> <lf> Includes 2 line fee...

10.0 CALIBRATION • The CBW scales are calibrated using metric weights and the CBWa scales can be calibrated using either metric or pound weights, depending on the weighing unit in use before calibration. • To start calibration turn the scale off and then turn it on again. Press the [Tare] and [%] ke...

11.0 ERROR CODES During the initial power-on testing or during operation, the scale may show an error message. The meaning of the error messages is described below. If an error message is shown, repeat the step that caused the message. If the error message is still shown then contact your dealer for...

12.0 REPLACEMENT PARTS AND ACCESSORIES If you need to order any spare parts and accessories, contact your supplier or Adam Equipment. A partial list of such items is as follows- • Power Supply Module • Main Power cord • Replacement Battery • • Stainless Steel Pan • In use cover • Printer, etc. 13.0 ...

WARRANTY INFORMATION Adam Equipment offers Limited Warranty (Parts and Labour) for the components failed due to defects in materials or workmanship. Warranty starts from the date of delivery. During the warranty period, should any repairs be necessary, the purchaser must inform its supplier or Adam ...