Adam Equipment 9520 - Manual

3.0   SET   UP   3.1   FEATURES   The   Stainless   Steel   AE   401   Indicator   is   a   general   purpose   weighing   indicator   for   use   with   strain   gauge   load   cells. The   indicator   offers:   • Large   clear   LCD   display   • Simple   user ‐ friendly   operations   • Full   ra...

3.2     CONNECTIONS   3.2.1   CONNECTION   OF   LOAD   CELL   For   better   performance   of   the   electronic   scale,   make   sure   to   connect   the   5   pin   round   plug   to   the   5   pin   socket   firmly   and   tighten   the   screw.   Please   see   figure   1:      1:   Pin   +IN...

3.3   DISPLAY   /   KEYBOARD   FUNCTION   The   keys   perform   the   following   functions:   KEYS   FUNCTION [O/I]   On/Off   function     Tare   the   scale     Zero   setting   of   the   scale;   range   of   zero   set   is   ±2%   of   total   [Mode]   Change   weighing   functions   and   w...

5.0   FUNCTIONS   5.1   ACCUMULATION   AND   PRINT   The   RS ‐ 232   output   will   print   one   line   for   each   weight   added   (press   the     [Print]   key)   and   then   print   a   total   of   all   the   weights   stored   into   memory   (press   the    [M+/Print]   key).          ...

6.0     RS ‐ 232   INTERFACE   The   RS ‐ 232   interface   can   be   used   to   record   weighing   information.     The   RS ‐ 232   connector   is   a   9   pin   d ‐ subminiature   socket   mounted   on   a   short   cable   at   the   rear   of   the   scale.   COMMUNICATION   CONNECTION:   P...

Total   from   Accumulation   memory:   1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 T O T A L n n n w w w w w . w w sp u u <cr> <lf> <lf> <lf> <lf> <lf> <lf>    Example   TOTAL_12_ _ _ 9 6 2 , 5 _ k g <cr><lf> <lf> <lf> <...

8.0   PARAMETERS     To   enable   the   parameters   and   calibration,   it   is   necessary   that   the   jumper   on   the   circuit   board   within   the   indicator    is   set   to   the   ON   position.     Place   the   jumper   on   the   pins   marked   ON,   at   JP1.     To   disable ...

8.4   BAUD   RATE   1) ‘b XXXX ’   will   display   on   the   screen.   The   value   shown   is   the   baud   rate.   2) Press   [Print]   to   switch   between   baud   rate   of   1200,   2400,   4800   and   9600.   3) Press   [Mode]   to   confirm.     8.5   SERIAL   PRINTOUT   PORT   CONFIGU...

9.0   CALIBRATION   Before   calibration,   remove   outer   case   of   the   indicator   and   set   circuit   breaker   at ‘On’   position   on   the   circuit   board   1) Press   [Tare]   key   until    ‘CALSP’   is   shown.   2) The   indicator   will   display ‘CALSP’   3) Press   [M+   Print...

10.0   ERROR   MESSAGES   AND   TROUBLE ‐ SHOOTING   Error Messages Possible Causes Suggestions Err E The   memory   has   failed.     Turn   off   power   switch   at   the   rear   of   the   scale   and   wait   for   ten   seconds.   Turn   on   again.    Err 1 A/D   value   is   less   than   n...

11.0   SPECIFICATIONS     A/D   conversion   speed   40   times/   sec.   Internal   resolution   ratio   400,000    External   resolution   ratio   1/1000 ‐ 1/15000   Power   supply   DC6V1.2Ah   Rechargeable   battery   And    AC/DC   12V   500mA   adapter   power;   Non ‐ linear   error   ＜ 0.016...

  ©   Copyright   by   Adam   Equipment   Co.   Ltd.     All   rights   reserved.     No   part   of   this   publication   may   be   reprinted   or   translated   in   any   form   or   by   any   means   without   the   prior   permission   of   Adam   Equipment.     Adam   Equipment   reserves  ...