Adam Equipment CBC SERIES - Manual

© Adam Equipment Company 2009 6 3.0 INSTALLATION 3.1 LOCATING THE SCALE • The scales should not be placed in a location that will reduce the accuracy. • Avoid extremes of temperature. Do not place in direct sunlight or near air conditioning vents. • Avoid unsuitable tables. The table or floor must b...

© Adam Equipment Company 2009 7 • The scale will show the current software revision number in the “ Weight ” display window, for example V3.06 . • Next a self-test is performed. At the end of the self-test, it will display “ 0 ” in all three displays, if the zero condition has been achieved. 4.0 KEY...

© Adam Equipment Company 2009 8 5.0 DISPLAYS The scales have three digital display windows. These are “ Weight ”, “ Unit Weight ” and “ Count ”. 5.1 WEIGHT DISPLAY It has 6-digit display to indicate the weight on the scale. Arrows above symbols will indicate the following: Low battery, as above Net ...

© Adam Equipment Company 2009 10 • As a product is added only the weight of the product will be shown. The scale could be tared a second time if another type of product was to be added to the first one. Again only the weight that is added after taring will be displayed. • When the container is remov...

© Adam Equipment Company 2009 11 by re-calculating it. To lock the Unit Weight and avoid re-sampling, press [U. Wt./Units] . • If the scale is not stable, the calculation will not be completed. If the weight is below zero, the “ Count ” display will show negative count. B. Entering a known Unit Weig...

© Adam Equipment Company 2009 12 automatically. • This feature is turned off as soon as the number of items added exceeds the count used as a sample. 6.3.4 Check-counting • Check-counting is a procedure to cause an alarm to sound when the number of items counted on the scale meets or exceeds a numbe...

© Adam Equipment Company 2009 13 6.3.6 Automatic Accumulated Totals • The scale can be set to automatically accumulate totals when a weight is placed on the scale. This eliminates the need to press the [M+] key to store values into the memory. However the [M+] key is still active and can be pressed ...

© Adam Equipment Company 2009 14 SETTING OF PIN • Display will show “ F2 ” “ Pin ”. This parameter allows setting of a new password number. • Press [Tare] . The “ WEIGHT ” display will show " Pin 1 " • Enter the new password number. The “ Unit Weight ” display will show dashes. Press [Tare] ...

© Adam Equipment Company 2009 15 • The displays will then show the calibration weight suggested as a whole number. For example: “ LoAd ” “ 04 ” “ KiLoS ” Either put this weight on the platform after the stable symbol is on or enter the desired value in whole integer and then press [Tare] . • Place t...

© Adam Equipment Company 2009 16 Specifications: Connector: The scale can be set to print text in English, French, German or Spanish. See the RS-232 parameters section for details. Data Format-Normal Output: Data Format- Memory Recall Print: Pressing the [MR] key will not send the totals to the RS-2...

© Adam Equipment Company 2009 17 In other languages the format is the same but the text will be in the language selected. Description ENGLISH FRENCH GERMAN SPANISH Print gross weight Gross Wt Pds Brut Brut-Gew Pso Brut Net weight Net Wt. Pds Net Net-Gew Pso Net Weight per unit counted Unit Wt. Pds u...

© Adam Equipment Company 2009 18 9.2 RS-232 SETUP The RS-232 interface uses parameters set by the user for language, baud rate and date format. Press and hold the [Print] key for 4 seconds to access the parameters. Press [U. Wt./Units] to scroll through the options and [Tare] to confirm the change a...

© Adam Equipment Company 2009 19 The scale will perform the following functions depending on the Accumulation and Print settings: ACCUMULATION FUNCTIONS PRINT FUNCTIONS AC Auto AC mAn AC oFF Print Auto Accumulate and print automatically Print automatically Accumulate and print when [M+] is pressed P...

© Adam Equipment Company 2009 20 • Press the [Tare] key to accept the time. The display will show the current date format. • Press the [Print] key to change the date format. Available formats are: “ Y-m-d ” year, month, day “ m-d-Y ” month, day, year “ d-m-Y ” day, month, year • Press the [Tare] key...

© Adam Equipment Company 2009 21 10.0 BATTERY AND BACKLIGHT OPERATION 10.1 BATTERY • The scales can be operated from the battery, if desired. The battery life is approximately 90 hours. • When the battery needs charging the arrow above the low battery symbol under the “ Weight ” display will turn on...

© Adam Equipment Company 2009 22 • Press [U. Wt./Units] to scroll through the options. “ EL on ” Sets the backlight to be on at all times. “ EL Au ” Sets the backlight to operate automatically when a weight is placed on the scale or a key is pressed. “ EL OFF ” Sets the backlight to be off. • Press ...

© Adam Equipment Company 2009 23 12.0 REPLACEMENT PARTS AND ACCESSORIES If you need to order any spare parts and accessories, contact your supplier or Adam Equipment. A partial list of such items is as follows- • Mains Power cord • Replacement Battery • • Stainless Steel Pan • In use cover • Printer...

© Adam Equipment Company 2009 24 WARRANTY INFORMATION Adam Equipment offers Limited Warranty (Parts and Labour) for the components failed due to defects in materials or workmanship. Warranty starts from the date of delivery. During the warranty period, should any repairs be necessary, the purchaser ...