Adam Equipment CBDa - Manuals

REMOTE SCALE CONNECTION The cable for the load cell goes to a 9 pin D-subminiature plug connector with the following connections: Pin numbers Connection Pins 1,2 - Excitation (0 V) Pins 4,5 + Excitation (+5 V) Pin 7 + Signal Pin 8 - Signal (The sense wires connections of a six wire load cell are not...

4.0 KEY DESCRIPTIONS [0-9, •] These keys are used to manually enter a value for tare weights, unit weight and sample size. A secondary function is to enter alpha-numeric characters for PLU descriptions etc. [CE] Pressing this key clears the unit weight or an erroneous entry. It also clears the memor...

[Local Rem] This key is used to select the local or remote scale. [Tare/Zero] This key has a combined Zero and Tare function. If the net weight is below ±2% of maximum then it acts as a Zero key. This sets the zero point for all subsequent weighing by setting the display to zero. It also tares the s...

5.2 UNIT WEIGHT WINDOW • This display will show the unit weight of a sample. This value is either entered by the user manually or computed by the scale. The unit of measure is either gram on all scales with kilogram selected as weighing unit or in pounds. • When the scale has determined that there i...

6.0 OPERATION • The basic weighing functions are same for both the scales- local and remote. However the number of weighing divisions may be less on the remote scale dependant on the total capacity of the load cell/s used. • Each scale (local or remote) has the ability to count parts based on the cu...

• When the container is removed a negative value will be shown. If the scale was tared just before removing the container this value is the gross weight of the container plus all products that were removed. The zero indicator will also be ON because the platform is back to the same condition as it w...

6.4 PLU (Product Look Up) Product Look-Up (PLU) numbers are used to store information about the commonly used items. The Tare Weight, Description of the product and Unit Weights for a particular item are recalled by entering the PLU number for ease of operation. The scale is capable of storing value...

Please find below an example for setting up “ PLU 27 ” with Description as “ M4 Nut ” and Unit weight of “ 0.015 ”. DISPLAYS ACTIONS Weight Unit weight Count REMARKS Press [PLU] “PLU ” “ - -“ “ “ - Press [2] , [7] “PLU ” “ 27” “ “ - Press [Pst] “PLU 27” “x x x x x x” “x x x ” The current description...

• If the tare value stored does not match the increment of the selected scale (For example, storing -1.446 for a scale with d=0.05) then round the tare weight depending on the scale resolution (For example, in this case, -1.45 would be used as the tare value). • If a PLU number is recalled that does...

PARA-METER SUB- PARAMETER DISPLAYS AND SETTINGS “bEEP"“ "oFF"” Beeper is set to off “bEEP"” "on I n "” Beeper is set to on between limits bEEP “bEEP” “"on oUt” ” Beeper is set to on outside limits (>0) “LitE"” “"oFF"” Backlight is set to off “LitE"” ...

P bAU d b 600 b 1200 b 2400 b 4800 b 9600 Sets the required baud rate (speed for the RS-232 communications). Default rate is 4800. PAritY 8 n 1 7 E 1 7 o 1 8 data bits, no parity 7 data bits, even parity 7 data bits, odd parity U id “U id” “ Abc234” “ “ Shows the current user ID (if any). Enter a ne...

the battery has a full charge. If it is red, the battery is nearly discharged and yellow indicates the battery is nearly charged. NOTE : It is recommended that the battery be charged before using the scale when the unit has been unpacked. 9.0 RS-232 OUTPUT Specifications: RS-232 output of weighing, ...

9.1 INPUT COMMANDS FORMAT The scale can be controlled with the following commands. Input Commands: • The scale has a number of commands to either cause an action or to enter data into memory. The commands are all upper case and are summarised below. • All commands are terminated by a carriage return...

9.2 STORING DATA VIA RS232 To store data the commands are: SUIDxxxxxx <CR> Store user ID data SSIDxxxxxx <CR> Store scale ID data SPLUxx,xxxxxxxxxxxx <CR> Store text data for PLUxx When PLU text data is stored the Scale used, current unit weight and current tare value is also store...

10.0 CALIBRATION ACTION DISPLAYS Press the [Tare/Zero] key during the self- test at power on. The scale will ask to enter the password. “ Pi n” Default Password is 0000. Enter “0” four times. Password can be changed in technical parameters. Press [Print] . “ Pi n” “ ----” Select the scale to be set ...

11.0 ERROR CODES During the initial power-on testing or during the operation, the scale may show an error message. The meaning of the error messages are described below. If an error message is shown, repeat the procedure that caused the message, such as turning the balance on, calibration or any oth...

12.0 TECHNICAL PARAMETERS The technical parameters accessed via the “ tEch ” prompt at the end of user parameters and are password controlled to prevent unauthorised access. These parameters set the metrology for the scales. Each scale is set independently. The parameters will set capacity, division...

WARRANTY INFORMATION Adam Equipment offers Limited Warranty (Parts and Labour) for the components failed due to defects in materials or workmanship. Warranty starts from the date of delivery. During the warranty period, should any repairs be necessary, the purchaser must inform its supplier or Adam ...