Bostitch 102272REVB 3/97 - Manual

Page 2 - FASTENERS

Stanley-Bostitch tools have been engineered to provide excellent customer satisfaction and are designed toachieve maximum performance when used with precision Stanley-Bostitch fasteners engineered to the sameexacting standards. Stanley-Bostitch cannot assume responsibility for product performance if...

Page 4 - BEFORE HANDLING OR OPERATING THIS TOOL:

TOOL OPERATION OPERATION WARNING: ! EYE PROTECTION which conforms to ANSI specifications and provides protectionagainst flying particles both from the FRONT and SIDE should ALWAYS be worn by theoperator and others in the work area when loading, operating or servicing this tool. Eyeprotection is requ...

Page 5 - TOOL OPERATION CHECK

TOOL OPERATION CHECK CAUTION: Remove all fasteners from tool before performing tool operation check. 1.TRIGGER OPERATED TOOL: A. With finger off the trigger, hold the tool with a firm grip on the handle. B. Place the nose of the tool against the work surface. C. Pull the trigger to drive. Release th...

Page 6 - BASIC TOOL OPERATION; MAINTAINING THE PNEUMATIC TOOL

;;;;;;;;;;;;;;;;; ;;;;;;;;;;;;;;;;; ;;;;;;;;;;;;;;;;; ;;;;;;;;;;;;;;;;; ;;;;;;;;;;;;;;;;; ;;;;;;;;;;;;;;;;; ;;;;;;;;;;;;;;;;; yyyyyyyyyyyyyyyyy yyyyyyyyyyyyyyyyy yyyyyyyyyyyyyyyyy yyyyyyyyyyyyyyyyy yyyyyyyyyyyyyyyyy yyyyyyyyyyyyyyyyy yyyyyyyyyyyyyyyyy ;; ;; ;; ;; ;; ;; ;; ;; ;; yy yy yy yy yy yy yy ...

Page 7 - TROUBLE SHOOTING; PROBLEM

TROUBLE SHOOTING PROBLEM CAUSE CORRECTION Trigger valve housing leaks air O-ring cut or cracked Replace O-ring Trigger valve stem leaks air O-ring/seals cut or cracked Replace trigger valve assembly Frame/nose leaks air Loose nose screws Tighten and recheck O-ring or Gasket is cut or cracked Replace...

Page 8 - AIR SUPPLY AND CONNECTIONS; LUBRICATION; COLD WEATHER OPERATION:

AIR SUPPLY AND CONNECTIONS WARNING: ! Do not use oxygen, combustible gases, or bottled gases as a power source for this tool as tool may explode, possibly causing injury. FITTINGS: Install a male plug on the tool which is free flowing and which will release air pressure from the tool when disconnect...

Page 9 - T40 TOOL SPECIFICATIONS; CONTACT TRIP; OPERATION

T40 TOOL SPECIFICATIONS All screws and nuts are metric. TOOL AIR FITTING: This tool uses a 1/4” N.P.T. male plug. The inside diameter should be .200” (5mm) or larger. The fitting must be capable of discharging tool air pressure when disconnected from the air supply. OPERATING PRESSURE: 70 to 100 p.s...

Page 10 - LOADING THE T40M TOOLS

1. Move pusher to rear until latched. 2. Use stick of staples to move cover spring to one side and drop over core of magazine.Repeat until magazine is loaded, allowingenough space for pusher to disengage fromthe latch. 3. Depress pusher latch pin with thumb and allow pusher to slide forward to engag...

Page 11 - QUICK RELEASE DOOR

Models T40S2, T40S4, T40S5, and T40SX contain a Quick Release Door feature. The door is designed to “pop” open if a jam occurs providing easy access for removing a jammed fastener. ALWAYS DISCONNECT AIR SUPPLY BEFORE CLEARING A JAMMED FASTENER. If the door does not “pop” open when a jam occurs, it c...

Page 13 - ACCESSORIES AVAILABLE

-13- ACCESSORIES AVAILABLE BC602 1 pint General Purpose Air-Tool Lubricant. BC603 1 pint “Winter-Formula” Air-Tool Lubricant. BC604 1 quart General Purpose Air-Tool Lubricant. N5583 4mm Hex Wrench for M5 screws. 851487 4mm Hex Wrench, long pattern for M5 screws. ORK1 O-Ring Kit BK6 Bumper Kit T40WBK...

Bostitch 102272REVB 3/97 - Manual

Table of Contents:

Summary

Other Bostitch Models