Bosch TS1015 - User Manual

-1-

for use with Bosch GTS15-10 Table Saw

Rear Outfeed Support TS1015

SAVE THESE INSTRUCTIONS

Read the manual for the use

of this accessory with the

tool. Always secure table saw to a sturdy plat-

form or stand to avoid saw and workpiece from

tipping over when pushing long workpieces past

the table.

Table saw may tip if long

workpieces are unsupported

past the outfeed support.

When ripping LONG BOARDS or LARGE PANELS,

always use a work support. The Bosch table saw

Rear Outfeed Support TS1015 is an ideal acces-

sory to use for these applications.

Contents

Item Description

Qty.

1

Support Bracket

2

2

M5x16mm Socket Head Bolt

4

3

Support Rod

2

4

Outfeed Support

1

5

Inner Washer

2

6

Outer Washer

2

7

Retaining Clip

4

8

Lock Knob

1

9

M5x12mm Socket Head Bolt

2

Assembly

(Fig. 1, Fig. 2, Fig. 3)
Tools Required:

5 mm hex wrench, pliers

1. Mount the Support Brackets

1

, positioned as

shown, on the underside of the table on either

side, and secure each Support Bracket

1

by

threading two M5x16mm Socket Head Bolts

2

into the pre-threaded holes in the table and

tightening them finger-tight.

2. Place an Inner Washer

5

(with the larger hole)

over the Shoulder

10

of a Support Rod

3

, and

position the Support Rod

3

with the Shoulder

10

in one of the holes on the Outfeed Support

4

.

3. On other side of the Outfeed Support

4

, place

an Outer Washer

6

(with the smaller hole)

on the Support Rod

3

, and attach it with an

M5x12mm Socket Head Bolt

9

, using a 5 mm

hex wrench to completely secure the bolt.

4. Repeat steps 2 and 3 to attach the other Sup-

port Rod

3

to the other hole in the Outfeed

Support

4

.

5. Insert the ends of the Support Rods

3

into the

Support Brackets

1

.

6. Using pliers, attach two Retaining Clips

7

to

the Support Rods

3

near the Outfeed Support

4

. These Retaining Clips

7

prevent the Outfeed

Support

4

from butting against the Table and

allow proper clearance for the Rip Fence.

7. Using pliers, attach two Retaining Clips

7

to

the ends of the Support Rods

3

.

8. Screw the Lock Knob

8

into a Support Bracket

1.

9. Move the Outfeed Support

4

in and out a few

times. If needed, adjust the position of the

Support Brackets

1

to enable smooth move-

ment of the Support Rod

3

.

10. Use a 5 mm hex wrench to completely tighten

the M5x16mm Socket Head Bolts

2

.

Operation

The Outfeed Support

4

was designed to extend the

depth of the table’s work surface to support longer

workpieces. The Outfeed Support

4

is adjustable.

Simply pull the center of the Outfeed Support

4

,

slide it to the desired position, and lock it in place

by tightening the Lock Knob

8

.

NOTE:

When the Outfeed Support

4

is

not in use,

slide it to its closed position. During transportation

and for storage, also tighten the Lock Knob

8

.

1609B08226_TS1015_Outfeed_Support_Assembly_OSI_20230404.indd 1

1609B08226_TS1015_Outfeed_Support_Assembly_OSI_20230404.indd 1

4/4/2023 11:00:33 AM

4/4/2023 11:00:33 AM