Audiovox APS 786 - Manual
Audiovox APS 786 – Manual, read for free online in PDF format. We hope this helps you resolve any issues you may have. If you have further questions, please contact us through the contact form.
Table of Contents:
- Page 2 – The APS-785 Remote Start/Alarm System is designed to be used with; Automatic Transmission; INSTALLATION OF THE MAJOR COMPONENTS:; HOOD AND TRUNK PIN SWITCHES:
- Page 3 – only! Although this combination; IT MUST NOT; be installed
- Page 5 – YELLOW START WIRE DETAIL; Ignition 2 Output
- Page 6 – WIRING CONNECTIONS: Multi Pin Accessory Input/Output Harness; Parking Light Flasher Feed; Parking Light Wiring Detail; SIREN
- Page 8 – General Motors VATS By-Pass Diagram
- Page 9 – Entry Illumination Ground Output; Entry Illumination Detail; Negative Inhibit Input; Grey w/ Black Trace Negative Inhibit Safety Shut Down Detail
- Page 10 – Brake Switch Positive Shutdown Detail
- Page 11 – Chassis Ground Source; Chassis Ground Connection Detail; Tachometer Input Signal; Tachometer Input Wiring Detail; Negative Door Trigger; Negative Door Switch Wiring Detail
- Page 12 – Delayed 300mA Pulsed Channel 3 Output; Channel 3 Relay Wiring Detail; 00mA Latched Channel 4 Output; WIRING THE 4 PIN AUXILIARY OUTPUT HARNESS; Pulsed Ground Output Before Start
- Page 13 – Pulsed Ground Output After Shutdown; Pin Control Switch:
- Page 14 – Wire Ground Switched Door Lock/Unlock Wiring Detail
- Page 16 – RF Programmable Features:
- Page 17 – To program these selectable features
- Page 18 – TIMED START OPERATION:; REMOTE START SELECTABLE FEATURES; To Program The Remote Start Selectable Features:; verifying you are in the feature program mode.
- Page 21 – MECHANICAL NEUTRAL SAFETY SWITCH CONSIDERATIONS:
- Page 22 – METHOD 1
- Page 23 – METHOD 2; To connect to the key in sensor circuit as shown for method 2:; COMPLETING THE INSTALLATION:; sure to clean the surface before affixing the label.
128-6531
1 of 24
Model APS 786
Installation Manual
4 Channel Remote Car Starter
With Full Feature Alarm System
Installation Instructions
This Unit Is Intended For Installation In Vehicles With
12 Volt Negative Ground Electrical Systems,
Gasoline or Diesel With True Tach Reference
And Automatic Transmissions Only.
Kit Contents:
Remote Start/Alarm Control Module
(2) - Four Button Anti Code Hopping Transmitters
4 Channel Code Learning Receiver
External Superheterodyne Antenna/Receiver
Mini Six Tone Siren
(1) - Multi Pin Input/Output Harness
(1) - Six Pin Power Harness
(1) - Four Pin Auxiliary Output Harness
(1) - Two Pin LED Indicator
(1) - Two Pin Valet / Programming Switch
(1) - Two Pin Control Switch
(1) - Four Pin Shock Sensor Harness
(1) - Two Pin Door Lock Harness
(1) - Dual Stage Shock Sensor
(1) - Starter Inhibit Relay and Socket
(2) - 30 Amp In-line Fuse Holders With Fuses
(1) - Pin Switch Hardware Bag
(2) - Under Hood Caution Labels
(1) - Installation Manual
(1) - Operator's Manual
(1) - Limited Warranty
(2) - Window Decals
"Loading the manual" means you need to wait until the file loads and becomes available for online reading. Some manuals are very large, and the time they take to appear depends on your internet speed.
Summary
128-6531 2 of 24 The APS-785 Remote Start/Alarm System is designed to be used with Automatic Transmission Vehicles Only! The unit provides a selectable ignition control that allows a number of selectable timed outputs for glow plug pre-heat which may be required for certain diesel vehicles, (see sel...
128-6531 3 of 24 THE RECEIVER/ANTENNA ASSEMBLY: The Superheterodyne Receiver Antenna Assembly provided with this unit allows routing from below thedash board for maximum operating range. Choose a location above the belt line (dashboard) of the vehiclefor best reception. Special considerations must b...
128-6531 5 of 24 YELLOW START WIRE DETAIL 5 GREEN Wire: Ignition 2 Output Connect this wire to the ignition 2 wire from the ignition switch. This wire will show + 12 volts when theignition key is turned to the "ON" or "RUN" position and is some cases the "START" or CRANK"...
