Page 2 - Table of Contents
2 Table of Contents 1. Introduction ................................................................................................................. 3 1.1 Package Contents ................................................................................................. 3 1.2 Features .................
Page 3 - Package Contents
3 1. Introduction Congratulations on your purchase of the Airlink101® Wireless 300N PCI Adapter. Its high bandwidth combined with extended wireless coverage delivers fast and reliable connection for all of your networking applications when used with other Airlink101® Wireless 300N products. A full r...
Page 5 - Allow; to continue with the installation.
5 Note: If the Autorun screen doesn’t appear automatically, or if you get a blank white screen, go to Start, Run, and type D:\Utility\Setup.exe (where D is the letter of your CD drive) and click OK. Windows Vista users: At this point, you may get a warning message like the one below. Make sure that ...
Page 6 - Click; at the welcome screen.; Next; to accept the default destination folder.
6 Step 4 Click Next at the welcome screen. Step 5 Click Next to accept the default destination folder.
Page 9 - and click; . If this screen does not appear, you can
9 Step 8 After the computer is restarted, Windows will ask to connect to Windows Update, select No, not this time and click Next . If this screen does not appear, you can skip to section 2.2.
Page 10 - Select; Install the software automatically
10 Step 9 Select Install the software automatically and click Next .
Page 11 - Continue Anyway; at the Windows Logo Screen.; Yes; at the Digital Signature Not Found prompt).; Install this driver software anyway; button when the
11 Step 10 Click Continue Anyway at the Windows Logo Screen. (For Windows 2000, click Yes at the Digital Signature Not Found prompt). For Windows Vista, click the Install this driver software anyway button when the security warning appears.
Page 12 - Finish
Page 13 - Configuring the Adapter; Note to Windows XP Users:; in the system tray and then
13 3. Configuring the Adapter This section describes how to connect your wireless adapter to a wireless network. Note to Windows XP Users: You must disable the Wireless Zero Configuration Utility in order to use the bundled Wireless Utility. Please follow the steps below to disable XP’s wireless uti...
Page 14 - Go to the; AP List; you wish to connect to, and click; Connect
14 Step 1 To open the utility, double click on the Wireless Monitor icon in the system tray at the bottom right-hand corner of your screen. Step 2 Go to the AP List tab, select the SSID (Network Name) of the wireless network you wish to connect to, and click Connect .
Page 16 - OK
16 When you click on it and click connect, a box will pop up requesting the wireless encryption key for the router. Enter the encryption key into the box and click OK .
Page 17 - If you are experiencing problems with the connection (unable to
17 Step 3 You should now be connected. You should see “Connected” in the top, right hand corner, and there will be a blue circle around the antenna icon next to the network name. Troubleshooting: If you are experiencing problems with the connection (unable to connect, low signal strength, slow conne...
Page 18 - Wireless Information; box at the top of the window provides you with the status of
18 4. Wireless Monitor This section describes the various functions of the Wireless Monitor that you can configure, including the settings of wireless encryption. 4.1 Wireless Information The Wireless Information box at the top of the window provides you with the status of the current connection, in...
Page 19 - to enable that profile.
19 4.2 AP List The AP List tab displays all the available wireless networks detected by the Wireless Adapter. Simply select the wireless network you wish to connect to and click Connect . If you have created multiple profiles, you can use the profile chooser at the bottom to select the specific prof...
Page 20 - Profile Settings; section of the wireless; My Wireless Networks; My Wireless Networks; box; New
20 4.3 Profile Settings This section provides instructions on using the Profile Settings section of the wireless monitor. The My Wireless Networks box lists the different profiles you’ve created for the different networks that you use. Profiles are automatically created and added to this list when y...
Page 21 - The; box will appear allowing you to specify the settings for your new; to save the changes.
21 The Profile Settings box will appear allowing you to specify the settings for your new profile or change settings for your existing profile. Once you are finished entering the settings, click OK to save the changes.
Page 22 - Configuring Encryption; Section 3; . The only time you will need to; then
22 4.4 Configuring Encryption This section describes the different types of encryption available and how to configure them. In most cases, encryption will be automatically configured and all that will need to be entered is the key, as described in Section 3 Step 2 . The only time you will need to ma...
Page 24 - Configuring WEP encryption
24 Configuring WEP encryption Select WEP from the Set Security Option box. Under Wired Equivalent Privacy (WEP) , you will want to select Shared or Open , depending on the router settings. In the Key box, you will want to type in the encryption key for the router. If you check the Show text in the p...
Page 25 - from the; Set Security Option; select either; TKIP; or; AES; depending on the settings for; KEY
25 Configuring WPA/WPA2-PSK Encryption (for home users) Select WPA/WPA2-PSK from the Set Security Option box. Under Passphrase Settings select either TKIP or AES depending on the settings for your router. Enter the encryption key into the KEY box.
Page 27 - to enter your authentication settings.
27 Configuring 802.1x authentication (for corporate networks) Select 802.1x from the Set Security Option box. Click on Advanced Config to enter your authentication settings.
Page 30 - Once that is done, click on the; to enable the profile.
30 Once that is done, click on the AP List . Select your new profile from the profile chooser and click Activate to enable the profile. You will need to configure all other computers that you are planning on connecting to your ad-hoc network with the same settings that you input on this screen. Ever...
Page 31 - WPS; ) is a new and easy way to configure the encryption for; WPS Connect; Choose your configuration method, either; Push Button; Pin Code
31 4.6 Wi-Fi Protected Setup (WPS) Wi-Fi Protected Setup™ ( WPS ) is a new and easy way to configure the encryption for your wireless network clients to connect to your router. If your wireless router does not support WPS feature or it is disabled on your router (WPS is disabled when you use WEP as ...
Page 32 - If you choose the Push Button method, make sure that you click on the; Protected Setup
32 Step 3a If you choose the Push Button method, make sure that you click on the Wi-Fi Protected Setup button.
Page 33 - If you choose the Pin Code method, write down the; PIN
33 Step 3b Push the WPS button on the router, and the blue LED will start blinking. The router will now start the handshake with the wireless adapter, then the connection will be built up in couple minutes. Step 4a If you choose the Pin Code method, write down the PIN and click Next .
Page 35 - on the WPS Connection screen.; Wireless; . Make sure that the; Enable
35 Step 5 Click Finish on the WPS Connection screen. Note: If you cannot connect successfully with WPS, you need to log in to your router’s configuration and click on Wireless . Then click Wireless security . Make sure that the Wi-Fi Protected Setup Enable box is checked.
Page 36 - address of the adapter.
36 4.7 About The About tab shows the Utility, Driver versions, and the MAC address of the adapter.
Page 37 - Appendix A – Features
37 Appendix A – Features Frequency Band • 2.4~2.5 GHz Standards • IEEE 802.11b / 802.11g • 802.11n draft 2.0 Interface • PCI Antenna type • 3 external 2dBi antenna Security • WPA-PSK (TKIP) • WPA2-PSK (AES) Transmitted Power • 802.11b: 17 dBm • 802.11g: 14 dBm • Draft 11n: 14 dBm Data Rate • Transmi...
Page 38 - Appendix B – Information; Federal Communication Commission Interference Statement; Reorient or relocate the receiving antenna.
38 Appendix B – Information Federal Communication Commission Interference Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interf...
Page 39 - Industry Canada Statement
39 Industry Canada Statement This device complies with RSS-210 of the Industry Canada Rules. Operation is subject to the following two conditions: 1) this device may not cause interference and 2) this device must accept any interference, including interference that may cause undesired operation of t...
Page 40 - Technical Support
40 Technical Support E-mail: [email protected] Toll Free: 1-888-746-3238 Web Site: www.airlink101.com *Theoretical maximum wireless signal rate derived from IEEE 802.11g standard and IEEE 802.11n draft specification version 2.0. Actual data throughput will vary. Network conditions and environme...
