Page 2 - Table of Contents
2 Table of Contents 1. Introduction ................................................................................................................. 3 1.1 Package Contents ................................................................................................. 3 1.2 Features .................
Page 3 - Package Contents
3 1. Introduction Congratulations on your purchase of the 300N Draft 802.11n Wireless PCI Adapter. The 300N PCI Adapter provides wireless data rate of up to 300 Mbps* when used with other AirLink101™ 300N wireless products. The high bandwidth combined with extended wireless coverage delivers fast an...
Page 5 - The Autorun screen will pop up. Select; Install Driver and Utility; Click; Next; at the welcome screen.
5 Step 3 The Autorun screen will pop up. Select Install Driver and Utility from the menu. Note: If the Autorun screen doesn’t appear automatically go to Start, Run, and type D:\Utility\Setup.exe (where D is the letter of your CD drive) and click OK. Step 4 Click Next at the welcome screen.
Page 6 - to accept the default destination folder.; Continue Anyway; at the Windows Logo Screen.; Yes; at the Digital Signature Not Found prompt).
6 Step 5 Click Next to accept the default destination folder. Step 6 Click Continue Anyway at the Windows Logo Screen. (For Windows 2000, click Yes at the Digital Signature Not Found prompt).
Page 7 - Verify; Yes, I want to restart my computer now; is selected and click; Finish; to
7 Step 7 Verify Yes, I want to restart my computer now is selected and click Finish to restart your computer. Step 8 After the computer is restarted, Windows will ask to connect to Windows Update, select No, not this time and click Next .
Page 10 - Verify Driver Installation; from your desktop and select
10 2.2 Verify Driver Installation To verify if the driver has been installed successfully, please perform the following steps. Step 1 Right-click on My Computer from your desktop and select Properties . Step 2 Select the Device Manager tab. (For Windows 2000/XP, select the Hardware tab first then cl...
Page 11 - Expand; Network adapters; from the list and verify that; Wireless PCI Adapter; is listed and no yellow question mark is beside it.
11 Step 3 Expand Network adapters from the list and verify that AirLink101 300N Wireless PCI Adapter is listed and no yellow question mark is beside it. If AirLink101 300N Wireless PCI Adapter is not listed, or you see a yellow question mark beside it, please re-install the driver again.
Page 12 - Configure the PCI Adapter; Note to Windows XP Users:
12 3. Configure the PCI Adapter This section describes how to connect your 300N Wireless PCI Adapter to a wireless network. Note to Windows XP Users: You must disable the Wireless Zero Configuration Utility in order to use the bundled Wireless Utility. Please follow the steps below to disable XP’s w...
Page 13 - To open the PCI Adapter’s utility go to; Wireless PCI Adapter > AirLink101 300N Wireless PCI Adapter; Go to the; AP List; you wish to connect to, and click; Connect
13 To open the PCI Adapter’s utility go to Start > (All) Programs > AirLink101 300N Wireless PCI Adapter > AirLink101 300N Wireless PCI Adapter Step 1 Go to the AP List tab, select the SSID (Network Name) of the wireless network you wish to connect to, and click Connect .
Page 14 - Profile Name; for your wireless setting and click; Verify that the; Network Name; matches the; SSID; of your wireless network and
14 Step 2 If encryption is not enabled for the selected access point / router, skip to step 6. Otherwise, enter a Profile Name for your wireless setting and click Next . Step 3 Verify that the Network Name matches the SSID of your wireless network and click Next .
Page 15 - the drop-down menu and click
15 Step 4 Select the proper encryption setting for your wireless router or access point from the drop-down menu and click Next . Step 5 Follow the on-screen instructions to complete the encryption settings. Click Complete when finished. Step 6 You should see a blue circle around the antenna icon ind...
Page 16 - Link Information; tab and click on the; More
16 Step 7 Go to the Link Information tab and click on the More button. Step 8 Verify that you are receiving adequate Signal Strength and Link Quality and that you have been assigned a valid IP address (instead of all 0’s). If you do not have adequate Signal Strength, try re-orienting the Access Poin...
Page 17 - Configure the Wireless Utility; Link Information; tab shows the current profile in use as well as details of the; button to see the details of the current network connection.
17 4. Configure the Wireless Utility This section describes the various functions of the Wireless Utility that you can configure, including the settings of wireless encryption. 4.1 Link Information The Link Information tab shows the current profile in use as well as details of the current network co...
Page 19 - The; Site Information
19 4.2 AP List The AP List tab displays all the available Access Points detected by the PCI Adapter. Simply select the desired Access Point you wish to connect to and click Connect . The Site Information displays a list of status for the selected AP, including the Channel number and the Encryption s...
Page 20 - Configure Encryption Settings; PCI Adapter; From the; tab, select the Access Point/Wireless Router you want to; Verify the; is correct and click
20 4.3 Configure Encryption Settings This section describes how to configure encryption settings for the PCI Adapter . Note: The encryption settings you set for the Adapter must match the same settings of the Access Point/Wireless Router; otherwise, the encryption will not work properly. Step 1 From...
Page 22 - WEP Step 5; Select the appropriate; Input Method; click; Complete; to finish the settings.
22 WEP Step 5 Select the appropriate Input Method , Key (password), Key Index , and click Next . WEP Step 6 Click Complete to finish the settings.
Page 24 - WPA Step 6
24 WPA Step 6 Click Complete to finish the settings. Step 7 You should see a blue circle around the antenna icon indicating a valid connection. A lock icon beside the antenna indicates the connection is encrypted.
Page 25 - Profile Setting; tab lists all the profiles you have created. You can create new; Add
25 4.4 Profile Setting The Profile Setting tab lists all the profiles you have created. You can create new profiles for different network environments. To add a new profile, follow the steps below: Step 1 Click on the Add button.
Page 26 - Enter a name for your new profile and click; and click
26 Step 2 Enter a name for your new profile and click Next . Step 3 Enter the SSID (Network Name) of the wireless network you want to connect to and click Next .
Page 27 - Configure any encryption setting if required and click; to finish the profile setting.
27 Step 4 Configure any encryption setting if required and click Next . Step 5 Click Complete to finish the profile setting.
Page 29 - Static IP Setting; New Setting
29 4.5 Static IP Setting To change the IP address of the wireless adapter to Static IP, follow the steps below: Step 1 On the last step of 4.4 Profile Setting , under IP setting, select New Setting and click Next . Step 2 Select Static . Step 3 Enter in the information and click Complete to finish t...
Page 30 - address of the; 00N Wireless PCI Adapter
30 4.6 About The About tab shows the Utility, Driver, and Firmware version as well as the MAC address of the 300N Wireless PCI Adapter .
Page 31 - Appendix A – Features
31 Appendix A – Features Frequency Band • 2.4~2.5 GHz Standards • IEEE 802.11b / 802.11g • Draft 802.11n Interface • PCI Antenna type • 3 external antennas with 2.6 dBi(A), 3.6 dBi(B), 0.9dBi(C) Gain Security • WPA-PSK (TKIP) • WPA2-PSK (AES) Transmitted Power • 802.11b: 17 dBm@1TX; 20 dBm@2TX • 802...
Page 32 - Appendix B – Information; Federal Communication Commission Interference Statement; Reorient or relocate the receiving antenna.
32 Appendix B – Information Federal Communication Commission Interference Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interf...
Page 33 - European Union Notice:; EN 300 328 Technical requirement for radio equipment
33 European Union Notice: Radio products with the CE marking comply with the R&TTE Directive (1999/5/EC), the EMC Directive (89/336/EEC) and the Low Voltage Directive (73/23/EEC) issued by the Commission of the European Community. Compliance with these directives implies conformity to the follow...
Page 34 - Technical Support
34 Technical Support E-mail: [email protected] Toll Free: 1-888-746-3238 Web Site: www.airlink101.com *Theoretical maximum wireless signal rate derived from IEEE 802.11g standard and IEEE 802.11n draft specification version 1.0. Actual data throughput will vary. Network conditions and environme...
