Page 2 - Visit our website for:; Register your product for better service:; CUSTOMER CARE AND SERVICE; General information and tips
CONTENTS 1. SAFETY INFORMATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 2. SAFETY INSTRUCTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 3. TECHNICAL INFORMATION ....
Page 4 - SAFETY INSTRUCTIONS; Installation
• If the supply cord is damaged, it must be replaced by the manufacturer, its service agent or similarly quali-fied persons in order to avoid a hazard. • The operating water pressure (minimum and maxi- mum) must be between 0,5 bar (0,05 MPa) and 8 bar(0,8 MPa) • The ventilation openings in the base ...
Page 5 - TECHNICAL INFORMATION; Dimensions
Water connection • Make sure not to cause damage to the water hoses. • The appliance is to be connected to the water mains using the new sup-plied hose-sets. Old hose sets mustnot be reused. • Before you connect the appliance to new pipes or pipes not used for a longtime, let the water flow until it...
Page 6 - PRODUCT DESCRIPTION
Water supply pressure Minimum 0,5 bar (0,05 MPa) Maximum 8 bar (0,8 MPa) Water supply 1) Cold water Maximum load Cotton 7 kg Spin speed Maximum 1600 rpm 1) Connect the water inlet hose to a water tap with a 3/4'' thread. 4. PRODUCT DESCRIPTION 1 2 3 8 9 5 6 7 4 10 11 12 1 Worktop 2 Detergent dispens...
Page 7 - Accessories; Spanner; To remove the transit bolts.; Plastic caps; To prevent possible leakage; Plastic hose guide; CONTROL PANEL
4.1 Accessories 1 2 3 4 1 Spanner To remove the transit bolts. 2 Plastic caps To close the holes on the rear sideof the cabinet after the removal ofthe transit bolts. 3 Anti-flood inlet hose To prevent possible leakage 4 Plastic hose guide To connect the drain hose on theedge of a sink. 5. CONTROL P...
Page 8 - On Off button; nutes before you press button; Programme knob; If the programme is completed but the symbol stays on:
9 Spin reduction button 10 Temperature button 5.1 On Off button 1 Press this button to activate or deacti-vate the appliance. A tune sounds whenthe appliance is activated.The AUTO Stand-by function automati-cally deactivates the appliance to de-crease the energy consumption when:• You do not use the...
Page 10 - PROGRAMMES; Functions
Spin phase is off. 'Rinse Hold' function ison. 5.10 Temperature button 10 Press button 10 to change the default temperature. - - = cold water 5.11 Acoustic signals function You can hear the acoustic signals when:• You activate the appliance.• You deactivate the appliance.• You press the buttons.• Th...
Page 11 - STAIN
ProgrammeTemperature Type of loadmax. weight of load Cycledescription Functions Extra Silent95° - Cold White and colouredcotton with normalsoil.max. 7 kg WashRinsesStop with water inthe drum STAIN 1) EXTRA RINSETIME SAVE 2) Synthetics60° - Cold Synthetic or mixedfabric items with nor-mal level of so...
Page 12 - Super Eco
ProgrammeTemperature Type of loadmax. weight of load Cycledescription Functions Curtains40° - Cold Set this programmeto wash curtains. Itadds automaticallythe prewash phase toclean the dust fromthe curtains.Do not put the deter-gent into the pre-wash compartment.max. 2,5 kg PrewashWashRinsesShort sp...
Page 13 - CONSUMPTION VALUES
7) Standard programmes for the Energy Label consumption values. According to regulation 1061/2010, these programmes are respectively the “standard 60° C cottonprogramme” and the “standard 40° C cotton programme”. They are the most efficientprogrammes in terms of combined energy and water consumption...
Page 14 - Press button; Loading the laundry; Open the appliance door.; Filling the detergent and
Off Mode (W) Left On Mode (W) 0.48 0.48 The information given in the charts above are in compliance with the EU Com-mision regulation 2015/2010 implementing directive 2009/125/EC. 8. BEFORE FIRST USE 1. To activate the drain system, put 2 li-tre of water in the main wash com-partment of the detergen...
Page 15 - This is the maximum level for the quantity of liquid additives.; Check the position of the flap
The detergent compartment for the prewash phase, the soakprogramme and for the stain function.Add the detergent for prewash, soak and stain remover beforethe start of the programme. The detergent compartment for the washing phase.If you use a liquid detergent, put it immediately before you startthe ...
Page 17 - To open the appliance door:; At the end of the
1. Press button 4 . The indicator flashes. 2. Change the function set. 9.7 Set the delay start 1. Press button 5 again and again un- til the display shows the number ofminutes or hours. The related sym-bols comes on. 2. Press button 4 , the appliance starts the countdown of the delaystart.When the c...
Page 18 - HINTS AND TIPS; The laundry load
10. HINTS AND TIPS 10.1 The laundry load • Divide the laundry in: white, coloured, synthetics, delicates and wool. • Obey the washing instructions that are on the laundry care labels. • Do not wash together white and col- oured items. • Some coloured items can discolour with the first wash. We recom...
Page 19 - CARE AND CLEANING; Descaling; gramme; Door seal; • Start a short programme for cotton at
Water hardness table Level Type Water hardness °dH °T.H. mmol/l Clarke 1 soft 0-7 0-15 0-1.5 0-9 2 medium 8-14 16-25 1.6-2.5 10-16 3 hard 15-21 26-37 2.6-3.7 17-25 4 very hard > 21 > 37 >3.7 >25 11. CARE AND CLEANING WARNING! Disconnect the appliance from the mainssupply before you clean...
Page 20 - Detergent dispenser; To clean the dispenser:; Pull the dispenser out.; Drain pump; • The display shows an alarm code be-
11.6 Detergent dispenser To clean the dispenser: 1 2 1. Press the lever. 2. Pull the dispenser out. 3. Remove the top part of the liquidadditive compartment. 4. Clean all the parts with water. 5. Clean the dispenser recess with abrush. 6. Put back the dispenser in the recess. 11.7 Drain pump Regular...
Page 21 - To clean the drain pump:; Open the drain pump door.
To clean the drain pump: 1. Open the drain pump door. 2. Pull the flap out to remove it. 3. Put a container below the recess ofthe drain pump to collect the waterthat flows out. 4. Press the two levers and pull for-ward the drainage duct to let thewater flow out. 1 2 5. When the container is full of...
Page 22 - • The indicator of button; To clean the water inlet filters:; Emergency drain
1 2 9. Clean the filter under the water tapand put it back in the pump into thespecial guides. 10. Make sure that you tighten correctlythe filter to prevent leakages. 11. Put the flap back and close the drainpump door. 11.8 The inlet hose filter and the valve filter It could be necessary to clean th...
Page 23 - Frost precautions; Remove the water inlet hose; TROUBLESHOOTING; - The appliance does not fill with; Problem; The water tap is closed.
Put the drainage duct back and close thedrain pump flap.When you drain the water with the emer-gency drain procedure, you must acti-vate again the drain system: 1. Put 2 litres of water in the main washcompartment of the detergent dis-penser. 2. Start the programme to drain thewater. 11.10 Frost pre...
Page 25 - The load is very small.; INSTALLATION; Fixing plate kit; Available from your authorized dealer.
Problem Possible cause Possible solution Leakages from the drainpump. Make sure that the drain pumpfilter is tight. The water drain hose isdamaged. Make sure that the water inlethose has no damages. You cannot openthe appliancedoor. The washing pro-gramme is in operation. Let the washing programmeen...
Page 26 - Unpacking; Remove the cardboard top.
13.2 Unpacking 1. Use the gloves. Remove the externalfilm. If necessary, use a cutter. 2. Remove the cardboard top. 3. Remove the polystyrene packagingmaterials. 4. Remove the internal film. 5. Open the door and remove all theitems from the drum. 26 www.aeg.com
Page 27 - Pull out the plastic spacers.
6. Put one of the polystyrene packag-ing elements on the floor behindthe appliance. Carefully put downthe appliance with the rear side onit. Make sure not to damage the ho-ses. 1 2 7. Remove the polystyrene protectionfrom the bottom. 8. Pull up the appliance in vertical po-sition. 9. Remove the powe...
Page 28 - Positioning and levelling
12. Put the plastic caps in the holes.You can find these caps in the usermanual bag. – We recommend that you keep the packaging and the transitbolts for when you move theappliance. – If the appliance is delivered in the winter months when thereare minus temperatures. Storeit at room temperature for ...
Page 29 - The inlet hose; • Connect the hose to the appliance.
CAUTION! Do not put cardboard, wood orequivalent materials below theappliance feet to adjust the level. 13.4 The inlet hose 20 O 20 O 20 O 45 O 45 O 45 O • Connect the hose to the appliance. Turn the inlet hose only left or right.Loose the ring nut to set it in the cor-rect position. • Connect the w...
Page 30 - Water drainage; With the plastic hose guide.
13.5 Water drainage There are different procedures to con-nect the drain hose: With the plastic hose guide. • On the edge of a sink.• Make sure that the plastic guide can- not move when the appliance drains.Attach the guide to the water tap orthe wall. • To a stand pipe with vent-hole. Refer to the ...
Page 31 - ENVIRONMENT CONCERNS
• Directly to a built-in drain pipe in the room wall and tighten it with a clip. You can extend the drain hose tomaximum 400 cm. Contact theservice centre for the other drainhose and the extension. 14. ENVIRONMENT CONCERNS Recycle the materials with thesymbol . Put the packaging inapplicable contain...
