Page 2 - Visit our website for:; Register your product for better service:; CUSTOMER CARE AND SERVICE; General information and tips
CONTENTS 1. SAFETY INFORMATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 2. TECHNICAL INFORMATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 3. PRODUCT DESCRIPTION . . . . ....
Page 3 - SAFETY INFORMATION
1. SAFETY INFORMATION Before the installation and use, read thismanual carefully:• For your safety and the safety of your property • To help the environment• For the correct operation of the appli- ance. Always keep these instructions with theappliance also if you move or give it to adifferent perso...
Page 4 - TECHNICAL INFORMATION; Dimensions
• Do not install and connect a damaged appliance. • Make sure to remove all packaging and transport bolts. • Make sure that the mains plug is dis- connected from the mains socket dur-ing installation. • Only a qualified person must do the electrical installation, the plumbingand the installation of ...
Page 5 - PRODUCT DESCRIPTION; Accessories
Water supply pressure Minimum 0,5 bar (0,05 MPa) Maximum 8 bar (0,8 MPa) Water supply 1) Cold water Hot water 2) Maximum load Cotton 8 kg Spin speed Maximum 1400 rpm 1) Connect the water inlet hose to a water tap with a 3/4'' thread. 2) Make sure that the hot water temperature of your domestic syste...
Page 6 - CONTROL PANEL; On Off button
1 2 3 4 1 Spanner To remove the transit bolts. 2 Plastic caps To close the holes on the rear sideof the cabinet after the removal ofthe transit bolts. 3 Cold and Hot anti-flood inlet ho-ses To prevent possible leakage 4 Plastic hose guide To connect the drain hose on theedge of a sink. 4. CONTROL PA...
Page 7 - If the programme is completed but the symbol stays on:
4.2 Programme knob 2 Turn this knob to set a programme. Therelated programme indicator comes on. 4.3 Display 3 A B C D The display shows: A • The maximum temperature of the programme. B • The default spin speed of the programme.• 'No Spin' 1) and 'Rinse Hold' symbols. C • The display symbols. 2) Sym...
Page 9 - PROGRAMMES; Functions
ter when the programme is comple-ted. Spin phase is off. 'Rinse Hold' function ison. 4.10 Temperature button 10 Press button 10 to change the default temperature. - - = cold water 4.11 Acoustic signals function You can hear the acoustic signals when:• You activate the appliance.• You deactivate the ...
Page 11 - Rinse; Super Eco; Cold
ProgrammeTemperature Type of loadmax. weight ofload Cycledescription Functions Spoelen - Rin-çage Rinse All fabrics One rinse with ad-ditiveLong spin SPIN REDUCTIONRINSE HOLDEXTRA RINSE 5) Gordijnen - Ri-deaux Curtains40° - Cold Set this programmeto wash curtains. Itadds automaticallythe prewash pha...
Page 12 - Woolmark Certificate
5) Press EXTRA RINSE button to add rinses. With a low spin speed the appliance performs delicate rinses and a short spin. 6) Set this programme to decrease the time and the consumption of energy and water. 7) Set this programme to have a good washing results and decrease the energy consumption. The ...
Page 13 - Synthetics 60°; BEFORE FIRST USE; Press button; Loading the laundry; Open the appliance door.
Off Mode (W) Left On Mode (W) 0.48 0.48 The values of power consumption of the «Off-mode » and «Left-on mode» arein compliance with the EU Commision regulation 2015/2010 implementing di-rective 2009/125/EC. Cold and hot water loading (The highest hot water temperature allowed is 55°C) Programme ) En...
Page 14 - This is the maximum level for the quantity of liquid additives.
Make sure that no laundry stays betweenthe seal and the door. There is a risk ofwater leakage or damage to the laundry. 7.2 Filling the detergent and additives The detergent compartment for the prewash phase and thesoak programme.Add the detergent for prewash and soak before the start of theprogramm...
Page 15 - Check the position of the flap; – Do not use gelatinous or thick; Setting and starting a; The indicator of button
Check the position of the flap 1. Pull out the detergent dispenser un-til it stops. 2. Press the lever down to remove thedispenser. 3. To use powder detergent, turn theflap up. 4. To use liquid detergent, turn theflap down. With the flap in the positionDOWN: – Do not use gelatinous or thick liquid d...
Page 16 - To open the appliance door:
5. Press button 4 to start the pro- gramme. The indicator of button 4 is on. The drain pump can operate fora short time when the appliancefills water. The appliance adjust auto-matically the cycle time to thelaundry you have put in thedrum to have perfect washingresults in the minimum neces-sary tim...
Page 17 - HINTS AND TIPS; The laundry load
• Press button 1 to deactivate the ap- pliance. After five minutes from theend of the programme, the energysaving function automatically deacti-vates the appliance. When you activate the applianceagain, the display show the endof the last set programme. Turnthe programme knob to set anew cycle. • Re...
Page 18 - Water hardness; soft; CARE AND CLEANING; Descaling
• To help the environment, do not use more than the correct quantity of de-tergent. • Obey the instructions that you find on the on packaging of these products. • Use the correct products for the type and colour of the fabric, the pro-gramme temperature and the level ofsoil. • If you use liquid dete...
Page 19 - • Start a short programme for cotton at; Door seal; To clean the dispenser:; Pull the dispenser out.
9.3 External cleaning Clean the appliance only with soap andwarm water. Fully dry all the surfaces. CAUTION! Do not use alcohol, solvents orchemical products. 9.4 Drum Regularly examine the drum to preventlimescale and rust particles. Only use special products to remove rustparticles from the drum.T...
Page 20 - Put back the dispenser in the recess.; Drain pump; • The display shows an alarm code be-; To clean the drain pump:; Open the drain pump door.
5. Clean the dispenser recess with abrush. 6. Put back the dispenser in the recess. 9.7 Drain pump Regularly examine the drainpump and make sure that it isclean. Clean the pump if:• The appliance does not drain the wa- ter. • The drum cannot turn.• The appliance makes an unusual noise because of the...
Page 21 - • The indicator of button; To clean the cold water inlet filters:
1 2 5. When the container is full of water,put the drainage duct back againand empty the container. Do steps 4and 5 again and again until no morewater flows out from the drainpump. 6. Pull back the drainage duct and turnthe filter to remove it. 7. Remove fluff and objects from thepump. 8. Make sure ...
Page 22 - Emergency drain; Remove the water inlet hose
1. Close the cold water tap. 2. Remove the cold water inlet hosefrom the cold water tap. 3. Clean the filter in the cold inlet hosewith a stiff brush. 4. Remove the cold inlet hose behindthe appliance. 5. Clean the filter in the cold valve witha stiff brush or a towel. 45° 20° 6. Install again the c...
Page 23 - TROUBLESHOOTING; - The appliance does not fill with; Problem; The water taps is closed. Open the water taps.
10. TROUBLESHOOTING The start of the appliance does not oc-cur or it stops during operation.First try to find a solution to the problem(refer to the table). If not, contact theservice centre. With some problems, the acousticsignals operate and the display showsan alarm code: • - The appliance does n...
Page 25 - Too much laundry load.; INSTALLATION; Fixing plate kit; Available from your authorized dealer.; Unpacking
Problem Possible cause Possible solution The appliance fillswith water anddrain immediately. The end of the drainhose is too low. Make sure that the drain hose isin the correct position. The washing re-sults are not satis-factory. The detergent you usedwas not sufficient or cor-rect. Increase the de...
Page 27 - Pull out the plastic spacers.
1 2 7. Remove the polystyrene protectionfrom the bottom. 8. Pull up the appliance in vertical po-sition. 9. Remove the power supply cable andthe drain hose from the hose hold-ers. 10. Remove the three bolts. Use the keysupplied with the appliance. 11. Pull out the plastic spacers. 12. Put the plasti...
Page 29 - • Connect the water inlet hoses to the; Water drainage; With the plastic hose guide.
• Connect the water inlet hoses to the cold and hot water taps with 3/4thread. CAUTION! Make sure that there are no leaksfrom the couplings. Do not use an extension hose ifone of the inlet hoses are tooshort. Contact the service centrefor the replacement of the shortinlet hose. Water-stop device A T...
Page 30 - Without the plastic hose guide.; • Directly to a built-in drain pipe in the
• On the edge of a sink.• Make sure that the plastic guide can- not move when the appliance drains.Attach the guide to the water tap orthe wall. • To a stand pipe with vent-hole. Refer to the illustration. Directly into adrain pipe at a height of not less than60 cm and not more than 100 cm. Theend o...
Page 31 - ENVIRONMENT CONCERNS
12. ENVIRONMENT CONCERNS Recycle the materials with thesymbol . Put the packaging inapplicable containers to recycle it.Help protect the environment andhuman health and to recycle wasteof electrical and electronic appliances. Do not disposeappliances marked with the symbol with the household waste. ...
