Adam Equipment ncsa 20 - Manual

Page 2 - SERVICE

1 Adam Equipment Company 2012 1.0 CONTENTS 1.0 CONTENTS ...........................................................................................1 1.1 KEY AND PANEL DESCRIPTION .....................................................2 2.0 OPERATION .......................................................

Page 3 - KEY

2 Adam Equipment Company 2012 1.1 KEY AND PANEL DESCRIPTION [ON/OFF] The power switch is located on the rear housing. Use this key to turn the counter ON and OFF. [START] Press the [START] key to continue checking following the detection of a counterfeit note. It can also be used to enter the parame...

Page 4 - COUNTING

3 Adam Equipment Company 2012 2.0 OPERATION 2.1 COUNTING FUNCTION To count the notes place them in between the guides at the rear of the machine. The sensor will detect the notes and feed them through displaying the number of notes counted on the Main Display. 2.2 BATCH FUNCTION The BATCH function a...

Page 5 - ADD

4 Adam Equipment Company 2012 2.3 ADD FUNCTION The ADD function allows you to accumulate and show a total number of notes that are being counted as well as a count for each separate counting process. When in ADD mode the ADD LED will light up. Press the [ADD] key and the BATCH display will show 0. P...

Page 6 - DUBIOUS

5 Adam Equipment Company 2012 2.4 DUBIOUS NOTE DETECTION The Magnetism (MG) and Ultraviolet (UV) functions are automatically enabled on Power up, these functions detect counterfeit notes as the counting process is performed. The MG and UV LED’s will be on. The degree of sensitivity for these can be ...

Page 7 - THE; PARAMETER; CODE; YES

6 Adam Equipment Company 2012 3.0 SETTING THE SENSITIVITY LEVEL Press the [START] key for 3-5 seconds to enter the Parameter setting section. Press the [+] key to select the parameter and the [-] key to change its setting. Once settings have been made press the [START] key to return to normal counti...

Page 8 - ERROR; MESSAGE

7 Adam Equipment Company 2012 4.0 ERROR MESSAGES, CODES AND SOLUTIONS 4.1 SENSOR ERROR TABLE MESSAGE ERROR C-1 START SENSOR PROBLEM C-2 BATCH SENSOR PROBLEM C-3 LEFT SIDE SENSOR PROBLEM C-4 RIGHT SIDE SENSOR PROBLEM C-5 UV SENSOR PROBLEM C-6 SPEED SENSOR PROBLEM C-7, C-8,C-9 MG SENSOR PROBLEM 4.2 BA...

Page 9 - REPLACING

8 Adam Equipment Company 2012 If any of the error messages appear please check to ensure the sensors are clean and the areas around them are clear. Clean with a soft cloth and dust the area with a brush. If the problem persists please contact your dealer. An adjustment can be made to suit the thickn...

Page 13 - PARTS; Part number

12 Adam Equipment Company 2012 5.8 REPLACING OTHER PARTS Other parts such as the large and small motor, transformer and ON/OFF switch can be changed by removing the side, rear and underside covers where appropriate. 6.0 PARTS LIST AND PICTURES NCSA 20plus Part number Description 7.00.4.0.0125 NCSA 2...

Page 14 - MAIN PCB

13 Adam Equipment Company 2012 MAIN PCB SPEED SENSOR DRIVE BELTS

Page 15 - POWER PCB

Page 16 - WARRANTY INFORMATION

15 Adam Equipment Company 2012 WARRANTY INFORMATION Adam Equipment offers Limited Warranty (Parts and Labour) for the components failed due to defects in materials or workmanship. Warranty starts from the date of delivery. During the warranty period, should any repairs be necessary, the purchaser mu...

Page 19 - Manufacturer’s Declaration of Conformity

Adam Equipment Company 2012 Manufacturer’s Declaration of Conformity This product has been manufactured in accordance with the harmonised European standards, following the provisions of the below stated directives: Restriction of the use of certain hazardous substances in electrical and electronic e...

Adam Equipment ncsa 20 - Manual

Table of Contents:

Summary

Other Adam Equipment Models