Yamaha DM2000 V2 - User Manual
Yamaha DM2000 V2 – User Manual, read for free online in PDF format. We hope this helps you resolve any issues you may have. If you have further questions, please contact us through the contact form.
Table of Contents:
- Page 2 – Cubase SX3 / DM2000 V2 Setup and Operation; Page; Controlling Cubase SX; Input Channel Controls
- Page 3 – Selected Channel Functions
- Page 6 – User Defined Keys; Brings the Project window to the front; Other Functions; METER BRIDGE
Cubase SX3 / DM2000 V2 Setup and Operation
Page
1
Cubase SX3 / DM2000 V2 Setup and Operation
This document describes setup and operation for remote control of Cubase SX from the
DM2000 digital mixing console. These instructions apply to DM2000 V2.0 or higher
and Cubase SX V3.0.0 or higher.
Driver Installation
1)
Connect your PC or Macintosh computer
The DM2000 should be connected to your computer by connecting the TO HOST
USB port on the DM2000 to a USB port on your computer.
2)
Install Driver
Once your computer is connected, you will need to install the USB-MIDI driver
included on the DM2000 CD-ROM. It is recommended that you install the latest
driver which can be downloaded
from
www.yamahaproaudio.com
Configuring DM2000 V2
1)
Press the [SETUP] display access key and select the MIDI/TO HOST screen.
2)
Set the DAW port assignment to USB 2-5 (this allows USB port 1 to be used for
the DM2000 Studio Manager Editor software). Note: you must use USB ports 2-
5 for DAW Control and USB port 1 for Studio Manager if you intend to use these
two applications simultaneously.
3)
Press the [REMOTE] display access key and assign CUBASE SX as the Target
for one of the Remote layers.
(See “About Remote Layers” in the DM2000 manual for more information.)
4)
Press the [LOCATOR] display access key and select DAW Control as the
function for the transport and locate keys. This allows the Cubase SX transport to
be controlled regardless of whether a Remote or Internal mixing layer is active.
5)
Press the relevant [REMOTE] LAYER button to select the Cubase SX Remote
Control Layer.
When the Cubase SX Remote Control Layer is selected, the DM2000’s control
surface controls Cubase SX rather than the internal mixing of the DM2000. In
order to control the DM2000, you need to select an Input Channel Layer or the
Master Layer. Audio mixing on the Input and Master Layers, and Automix
continues while the Cubase SX Layer is selected.
"Loading the manual" means you need to wait until the file loads and becomes available for online reading. Some manuals are very large, and the time they take to appear depends on your internet speed.
Other Manuals for Yamaha DM2000 V2
Summary
Cubase SX3 / DM2000 V2 Setup and Operation Page 2 Configuring Cubase SX V3.0.0 or higher 1) Click on the ‘Devices’ menu and select ‘Device Setup’. 2) Click on the ‘ + ’ icon (Add Device), then click on ‘Yamaha DM2000 V2’. This will cause Yamaha DM2000 V2 to appear in the Devices column on the left s...
Cubase SX3 / DM2000 V2 Setup and Operation Page 3 level shown in the fluorescent display section. In this mode, each send can be switchedOn/Off by pressing the encoder. Selected Channel Functions Pressing any of the DISPLAY switches in the SELECTED CHANNEL section ofDM2000 will cause the VST Audio C...
Cubase SX3 / DM2000 V2 Setup and Operation Page 6 User Defined Keys When DM2000 is used to remotely control Cubase SX, the following User Defined Keyshave permanently assigned functions: UDEF 1: Brings the Project window to the front UDEF 2: Scrolls channels down in banks of 8 UDEF 3: Scrolls channe...
