Page 3 - Table of contents
XEROX WIDE FORMAT 510 DP OPERATOR MANUAL i Table of contents EMC notices............................................................................................................................................................. iii Australia/New Zealand................................................
Page 5 - EMC notices; Australia/New Zealand; Canada
XEROX WIDE FORMAT 510 DP OPERATOR MANUAL iii EMC notices Australia/New Zealand Changes or modifications to this equipment not specificallyapproved by Fuji Xerox Australia PTA. Limited may void the user’sauthority to operate this equipment. Shielded cables must be used with this equipment to maintain...
Page 6 - Japan
EMC NOTICES iv XEROX WIDE FORMAT 510d dp OPERATOR MANUAL Japan This is a Class A product based on the standard of the VoluntaryControl Council for Interference by Information TechnologyEquipment (VCCI). If this equipment is used in a domesticenvironment, radio disturbance may arise. When such troubl...
Page 7 - Safety notes
XEROX WIDE FORMAT 510 DP OPERATOR MANUAL v Safety notes Your system has been designed and tested to meet strict safetyrequirements. These include safety agency examination andapproval plus compliance with established environmentalstandards. Please read the following instructions carefully before ope...
Page 9 - Introduction; Organization and content of this manual
XEROX WIDE FORMAT 510 dp OPERATOR MANUAL vii Introduction Congratulations on acquiring your new XEROX W ide Format510 dp . Xerox looks forward to supporting you and helping you increases your printing productivity. The XEROX Wide Format 510 dp is available as a standalone printer with an AccXES cont...
Page 10 - Terminology used in this manual; Conventions used in this manual
INTRODUCTION viii XEROX WIDE FORMAT 510d dp OPERATOR MANUAL Chapter 5 Care This chapter contains instructions for replacing the toner cartridgeand toner waste bottle and cleaning the printer surface. It alsolists the supplies needed and the procedure for ordering them. Chapter 6 Problem solving This...
Page 11 - Printer overview; Printer orientation
XEROX WIDE FORMAT 510 dp OPERATOR MANUAL 1 1. Printer overview This chapter shows the orientation of the printer. It also illustratesand describes its main components, as well as the elements of thecontrol panel. Printer orientation The illustration below shows the printer orientation. You must befa...
Page 12 - Main components
PRINTER OVERVIEW 2 XEROX Wide Format 510 dp OPERATOR MANUAL Main components 1. Output tray Prints exit the printer face up onto this tray. This tray holds up to100 prints of all sizes (including mixed sizes). The tray can beraised for access to the cut sheet feed-in shelf and the mediasupply drawers...
Page 14 - Control panel
PRINTER OVERVIEW 4 XEROX Wide Format 510 dp OPERATOR MANUAL Control panel The control panel is located on top of the front side of the printer.It consists of a graphic display, a message display, severalfunction keys, and a numeric keypad. 1. Graphic display This is an illustration of the printer wi...
Page 17 - Powering on and off; Powering on
XEROX WIDE FORMAT 510 dp OPERATOR MANUAL 7 2. Powering on and off This chapter describes the procedures for powering on andpowering off. It also describes the power consumption modes. Powering on To power on: 1. Switch the circuit breaker to the On ( I ) position. This turns on power to the Printer....
Page 18 - Powering off; Power consumption modes
POWERING ON AND OFF 8 XEROX Wide Format 510 dp OPERATOR MANUAL Powering off To power off: 1. Switch the printer power switch to the Off ( O ) position. This turns off the printer. 2. Switch off the Controller. 3. Switch the circuit breaker to the Off ( O ) position. This turns off power to the Print...
Page 19 - Media; When a media roll empties
XEROX WIDE FORMAT 510 dp OPERATOR MANUAL 9 3. Media This chapter provides the following information: • A listing of the ways in which the printer notifies you when a media roll is low or empty • The procedure for loading roll media into the media drawers • The procedure for specifying the media size...
Page 20 - Loading the roll media
MEDIA 10 XEROX WIDE FORMAT 510 dp OPERATOR MANUAL Loading the roll media To load a media roll: 1. Raise the output tray all the way so that it rests on top of the printer. 2. Lift the handle of the applicable drawer and open the drawer all the way. NOTE: In some locations, high or low humidity affec...
Page 24 - Changing the roll media size and type
MEDIA 14 XEROX WIDE FORMAT 510 dp OPERATOR MANUAL Changing the roll media size and type Whenever you open a media drawer, the message displayprompts you to change the type or width of the media. If you havenot changed the type or width of the roll media in the drawer, pressthe Exit key. If you have ...
Page 26 - Using the cut sheet feed-in shelf
MEDIA 16 XEROX WIDE FORMAT 510 dp OPERATOR MANUAL Using the cut sheet feed-in shelf When the correct media size or type is not loaded in the printer,you can bypass the media drawers and manually load cut sheetsinto the printer. If large size cut-sheet prints, portrait D-size (A1) oe E-size (A0),are ...
Page 27 - Automatic media roll switching
MEDIA XEROX WIDE FORMAT 510 dp OPERATOR MANUAL 17 Automatic media roll switching The printer has an automatic roll-switching feature that allows it toswitch to another roll when the roll in use empties. This featureprovides for longer continuous operation of the printer. Automatic switching is possi...
Page 29 - Setup Menu options
XEROX WIDE FORMAT 510 dp OPERATOR MANUAL 19 4. Off-line Setup Menu The printer has an off-line Setup Menu that allows you tocustomize the printer and the AccXES controller to meet yourparticular requirements. Setup Menu options The Setup Menu has the following options: • Utilities • Setup I/O Ports ...
Page 30 - Printer Menu
OFF-LINE SETUP MENU 20 XEROX WIDE FORMAT 510 dp OPERATOR MANUAL Printer Menu The Printer Menu allows you to control the operation of the printer.This menu contains six options. The table below describes thePrinter Menu options and their sub-options. Table 1. Printer Menu options Option Sub-option Fu...
Page 32 - Accessing the Printer Menu
OFF-LINE SETUP MENU 22 XEROX WIDE FORMAT 510 dp OPERATOR MANUAL Accessing the Printer Menu Note: If there is a Scanner connected, the message displayed willbe SYNERGIX CS 510dp. If there is no Scanner connected themessage will be SYNERGIX PS 510dp. To access the Printer Menu: 1. Press the On-line/Of...
Page 33 - Setting the timers; Adjusting the print density
OFF-LINE SETUP MENU XEROX WIDE FORMAT 510 dp OPERATOR MANUAL 23 Setting the timers To set the Power Saver mode and Rest mode timers: 1. Access the PRINTER MENU. See "Accessing the Printer Menu" in this chapter. 2. Press the Previous or Next key until TIMERS is displayed. 3. Press the Enter k...
Page 34 - Specifying the finisher configuration type; Performing printer diagnostics
OFF-LINE SETUP MENU 24 XEROX WIDE FORMAT 510 dp OPERATOR MANUAL Specifying the finisher configuration type Note: If there is a Scanner connected, the message displayed willbe SYNERGIX CS 510dp. If there is no Scanner connected themessage will be SYNERGIX PS 510dp. To specify the finisher configurati...
Page 35 - Displaying the billing meter counts
OFF-LINE SETUP MENU XEROX WIDE FORMAT 510 dp OPERATOR MANUAL 25 • The display will indicate " SYNERGIX CS 510 dp IDLE" or "SYNERGIX PS 510 dp " Viewing the recent fault log Note: If there is a Scanner connected, the message displayed willbe SYNERGIX CS 510dp. If there is no Scanner c...
Page 37 - Care; When the toner cartridge needs replacement
XEROX WIDE FORMAT 510 dp OPERATOR MANUAL 27 5. Care The printer requires a minimum of operator maintenance. You willneed to replace the toner cartridge and toner waste bottle whenthe cartridge empties. You also will need to clean the outsidesurface of the printer when necessary. This chapter provide...
Page 38 - Replacing the toner cartridge
CARE 28 XEROX WIDE FORMAT 510 dp OPERATOR MANUAL Replacing the toner cartridge To replace the toner cartridge: CAUTION: Toner identified for use in the XEROX Wide Format 510 dp is a two-component material made specifically for this printer. Use of toner not identified for the XEROX Wide Format510 dp...
Page 41 - Replacing the toner waste bottle
CARE XEROX WIDE FORMAT 510 dp OPERATOR MANUAL 31 Replacing the toner waste bottle Each time you replace the toner cartridge, you must replace thetoner waste bottle as well. To replace the toner waste bottle: 1. Open the front door. .
Page 44 - Cleaning the printer surface
CARE 34 XEROX WIDE FORMAT 510 dp OPERATOR MANUAL Cleaning the printer surface As needed, clean the outside surfaces of the printer. Use a cleancloth dampened with mild soap and water. Do not pour or sprayliquid directly on any part of the printer.
Page 45 - Ordering supplies; Supply order list; Supply order procedure
CARE XEROX WIDE FORMAT 510 dp OPERATOR MANUAL 35 Ordering supplies This section provides information for obtaining supplies for yourprinter. Supply order list The XEROX Wide Format 510 dp uses the following supplies: • Toner cartridge and toner waste bottle: The printer is shipped with one toner car...
Page 47 - Problem solving; Clearing media jams
XEROX WIDE FORMAT 510 dp OPERATOR MANUAL 37 6. Problem solving This chapter provides information for resolving various problemsthat can occur during the operation of the printer. It containsinstructions for clearing media jams. It also includes status codeand error message tables, as well as a gener...
Page 48 - Fuser area jam; To clear a jam in the fuser area:
PROBLEM SOLVING 38 XEROX WIDE FORMAT 510 dp OPERATOR MANUAL Fuser area jam To clear a jam in the fuser area: 1. Raise the output tray all the way so that it rests on top of the printer. WARNING: Do not touch the fuser roll while clearing media jams in the fuser area. The fuser roll is very hot and c...
Page 50 - Cutter area jam; To clear a jam in the cutter area:
PROBLEM SOLVING 40 XEROX WIDE FORMAT 510 dp OPERATOR MANUAL Cutter area jam To clear a jam in the cutter area: WARNING: The cutter blade is very sharp. Do not touch the cutter blade when clearing media jams in the cutter area. 1. Squeeze the latches on the cut sheet feed-in drawer and open the drawe...
Page 51 - Roll media drawer jams; To clear a jam in a roll media drawer:
PROBLEM SOLVING XEROX WIDE FORMAT 510 dp OPERATOR MANUAL 41 Roll media drawer jams To clear a jam in a roll media drawer: 1. Raise the output tray all the way so that it rests on top of the printer. 2. Lift the handle of the applicable drawer and open the drawer all the way. NOTE: In some locations,...
Page 54 - Status codes
PROBLEM SOLVING 44 XEROX WIDE FORMAT 510 dp OPERATOR MANUAL Status codes The status codes shown in the table below may appear on themessage display. Follow the instructions in the table before callingfor service. Table 2. Status Code Table Status code Explanation C0.-- This code indicates a cutter p...
Page 55 - Error messages
PROBLEM SOLVING XEROX WIDE FORMAT 510 dp OPERATOR MANUAL 45 Error messages The error messages shown in the table below may appear on themessage display. Follow the instructions in the table before callingfor service. Table 3. Error Message Table Error Message Problem Solution CHECK FOLDERFOLDER COMM...
Page 56 - Problem solving table
PROBLEM SOLVING 46 XEROX WIDE FORMAT 510 dp OPERATOR MANUAL Problem solving table The table below lists some conditions that may occur during theoperation of the printer. You may be able to resolve the problemsby following the suggested solutions in the table. For problemsbeyond the scope of this ta...
Page 57 - Calling for service
PROBLEM SOLVING XEROX WIDE FORMAT 510 dp OPERATOR MANUAL 47 Calling for service When you experience a problem with the printer, you may be ableto resolve it by referring to the procedures and tables in thischapter. If you are unable to resolve the problem, call your local XeroxEngineering Systems of...
Page 59 - Technical data; Product specifications
XEROX WIDE FORMAT 510 dp OPERATOR MANUAL 49 7. Technical data This chapter provides the product and media specifications for theXEROX Wide Format 510 dp . It also provides the space requirements for normal operation after product installation. Product specifications Table 5. Hardware Specifications ...
Page 61 - Media specifications
TECHNICAL DATA XEROX WIDE FORMAT 510 dp OPERATOR MANUAL 51 Media specifications Table 8. Media Specifications Media type Recommended media types: Bond – 20 to 24 lb (80 to 90 gsm) xerographic roll paper or cut sheetsVellum/tracing – 20 lb (80 gsm)Film - 4-millimeter thickness, double matte, heat sta...
Page 62 - Space requirements
TECHNICAL DATA 52 XEROX WIDE FORMAT 510 dp OPERATOR MANUAL Space requirements The illustration below shows the space requirements for normaloperation of the printer after installation. The height clearance from the floor to the nearest overheadobstruction within the floor space requirement is 78 inc...
