Xantech YiAK-K1000-01A - Manual
Xantech YiAK-K1000-01A – Manual, read for free online in PDF format. We hope this helps you resolve any issues you may have. If you have further questions, please contact us through the contact form.
Table of Contents:
- Page 2 – Power
- Page 3 – Rear Panel Connections; Installation and Connection; Step One – Prepare and Install the Wiring; Figure 1
- Page 4 – Step Two – Install an Optional IR Sensor; Wiring Chart 2; Step Three – Install the KP 1 In the Wall; Step Four – Connect the KP 1 to the PA 4000; Figure 2
KP 1
In-Wall Keypad
Power for the Digital Revolution
™
Decora is a registered trademark of Leviton Manufacturing Company, Inc.
Micro Link is a trademark and Xantech is a registered trademark of Xantech Corporation.
Harman Kardon is a registered trademark, and Power for the Digital Revolution is a trademark,
of Harman Kardon, Inc.
250 Crossways Park Drive, Woodbury, New York 11797
1-800/422-8027 (USA only) Fax: 516/682-3523
© 2001 Harman Kardon, Incorporated
Printed 9/01
Part No. YiAK-K1000-01A
Introduction
Congratulations!
As the owner of a KP 1 in-wall keypad, you own an
accessory that adds convenience and versatility to your home audio system
by providing independent control in each room or zone powered by a
Harman Kardon PA 4000 multichannel power amplifier. The elegant, three-
button design offers power on/off and volume control and is prewired to
accept an optional infrared (IR) sensor to allow remote control of virtually any
device equipped with a remote IR input.
The KP 1 uses an optional Decora
®
-style cover plate for coordination with
other wall-mounted switches. The KP 1 does not require an external power
supply, as all needed power is provided through the connection to the
PA 4000.
In order to fully enjoy the benefits of remote keypad control, please take a
few minutes to read this owner’s guide. It contains important information that
will guide you step by step through the correct and safe installation of your
keypad. If you do not have experience installing in-wall electrical and
telecommunications components, we recommend that you have the KP 1
installed by a properly trained professional.
If you have any questions about this product, its installation or its operation,
please contact your retailer or custom installer. They are your best source of
product information.
Features
■
Elegant, Three-Button Design
■
Up to Four KP 1 Keypads May Be Attached to the PA 4000 for
Independent Control of Separate Rooms and Zones
■
Accepts Optional IR Sensor That Transmits Commands to Most
Remote-Controllable Products Through a PA 4000
■
Designed for Use With Optional Decora-Style Wall-Plate That
Blends in With Other In-Wall Electrical Components
■
Mounts in Standard Electrical Junction Box or With Plaster Ring
■
RJ-45 Connector Offers Easy Installation With PA 4000 Amplifier
■
3-Pin Eurostyle Connector for Optional IR Sensor
Typographical Conventions
In order to help you use this guide with the front panel controls and rear panel connec-
tions for both the KP 1 and PA 4000, certain conventions have been used.
Example
– indicates a specific front panel button or rear panel connection jack
1
– indicates a KP 1 front panel control or feature
¡
– indicates a KP 1 rear panel connection or feature
a
– indicates a PA 4000 rear panel connection or switch
"Loading the manual" means you need to wait until the file loads and becomes available for online reading. Some manuals are very large, and the time they take to appear depends on your internet speed.
Summary
Important Safety and Installation Information! Wire Separations Low-voltage control wiring systems must always be installed to minimize the possibilityof accidental contact with wiring carrying hazardous voltage. Never place any wiringnear bare power wires or lightning rods, antennas, transformers, ...
Rear Panel Connections ¡ Cover Plate Screwholes – After you have completed installation, these screw- holes accept the screws supplied with your Decora-style cover plate to attach it to the KP 1. ™ Mounting Screw Slots – Use the supplied machine screws to attach the KP 1 to an electrical junction bo...
Step Two – Install an Optional IR Sensor If you are installing the optional IR sensor, you also need to prepare the sensor’s ribboncable. The recommended Xantech 490-00 Micro Link comes with a 7-foot long, 3-con-ductor ribbon cable. Trim the ribbon cable to 3 or 4 inches. Strip the wire ends 1 to 1-...
