Page 2 - English; Safety; Read all safety information before operating
English 2 Safety Safety Important Safety Information Read all safety information before operating the equipment. Save these instructions Indicates a hazardous situation which, if not avoided, could result in death or serious injury. a) To reduce the risks of fire or explosion, electrical shock and t...
Page 3 - Gasoline Engine Safety
English 3 7. Do not kink or over-bend the hose. Airless hose can develop leaks from wear, kinking and abuse. A leak can inject material into the skin. 8. Do not expose the hose to temperatures or pressures in excess of those specified by manufacturer. 9. Do not use the hose as a strength member to p...
Page 4 - What’s in; Start; GS-07 Spray Gun Assembly
English 4 What’s in the box?* Start *Certain parts of the sprayer will not be assembled out of the box. Be sure to read Assembly instructions, page 6. Notice: Refer to the engine manufacturer’s instruction manual for complete engine information. Heed all cautions and warnings.Note: The engine on the...
Page 5 - Proper use
English 5 Proper use and functions Start Controls and Functions Sprays a variety of paints (oil-based and latex), primers, stains, preservatives and other nonabrasive materials. Do not use. . . This pump should not be used with textured materials, block filler, asphalt sealer or materials containing...
Page 7 - Pressure Relief; *Perform when instructed; Important Safety Warning
English 7 Safety Start Pressure Relief Procedure* *Perform when instructed Start Important Safety Warning Be sure to follow the Pressure Relief Procedure when shutting the unit off for any purpose. This procedure is used to relieve pressure from the spray hose. Failure to do so could result in serio...
Page 8 - Material
English 8 2. Load Material Start You will need: • The material you plan to spray • Flat blade screwdriver • Piston Oil™ • Waste bucket 1. Remove AutoOiler cap with a flat blade screwdriver. Squirt Piston Oil into the AutoOiler. Replace cap. 2. Push AutoOiler button 2-5 times to lubricate the fluid s...
Page 9 - Material to; OR
You will need: • Waste bucket • Scrap material / cardboard • Drop cloths to protect floors and furnishings from overspray ImPOR´TANT: When placed on a smooth surface, the vibration of the running engine may cause the unit to move forward or backward slightly. Avoid placing the unit on an inclinded s...
Page 10 - Spraying; Hold the Spray Gun Level; CORRECT
English 10 4. Practice Spraying Start You will need: • Scrap material / cardboard Notes: If the spray pattern becomes distorted or stops completely while the gun is triggered, follow any or all the procedures listed on pages 12-14.If you plan to be away from your spray project for more than one hour...
Page 11 - Spray Pattern
English 11 Spray Pattern Overlap Your Strokes Spray Technique 50% Overlap 8” - 10” (20 - 25 cm) ! GOOD SPRAY PATTERN BAD SPRAY PATTERN: TAILING CORRECT See page 12-14 Start stroke End stroke Pull trigger Release trigger Move steadily CORRECT CORRECT INCORRECT Tip: Flex your wrist as you move in orde...
Page 12 - Clear the
English 12 Spraying Troubleshooting - Clear the Spray Tip Start You will need: • Scrap material / cardboard Do not attempt to unclog or clean the tip with your finger. High pressure fluid can cause injection injury. 1. Lock the spray gun. 2. Rotate spray tip 180 degrees from its current position. No...
Page 13 - Clean the Spray
English 13 Spraying Troubleshooting - Clean the Spray Gun Filter Start You will need: • Wrench • Warm, soapy water for latex material • Mineral spirits for oil based materials • Replacement spray gun filter (if necessary)ImPORTANT: Never clean the filter by poking it with a sharp object. 1. Peform t...
Page 14 - Clean the
English 14 Spraying Troubleshooting - Clean the Inlet Filter Start You will need: • Warm, soapy water for latex material • Mineral spirits for oil based materials ImPORTANT: make sure your floors and furnishings are covered with drop cloths to prevent accidental drips. 1. Unscrew the inlet filter fr...
Page 15 - Short Term; Shutdown
English 15 Short Term Storage Start English You will need: • Water • Plastic bag or bucket • Rags • Stir stick This procedure should be used when taking a short term break or when ending your project for the day. If your break is longer than 16 hours follow Cleanup instructions, page 16. Instruction...
Page 16 - Cleanup; Cleaning notes - read before cleaning; STOP; or
English 16 Cleanup Start You will need: • A water source that can be delivered with a garden hose (latex materials only) • Mineral spirits if using oil-based material • Empty waste container • A container with warm, soapy water • When using latex material, clean sprayer and components with warm, soa...
Page 18 - Materials
English 18 Cleanup - Oil-Based Materials Start You will need: • Mineral spirits if using oil-based material • Warm, soapy water if using latex material • Waste container Follow these steps if you sprayed oil-based materials, or if you sprayed latex materials and do not have a garden hose available. ...
Page 19 - Cleaning the; OIL
English 19 Cleaning the Spray Gun Components Start You will need: • Soft bristled brush • Light household oil • Warm, soapy water if using latex material • Mineral spirits for oil based material • WrenchImPORTANT: DO NOT use any silicone- based lubricants to clean or lubricate the spray gun. 1. Pefo...
Page 20 - Long Term
English 20 Long Term Storage Start You will need: • Light household oil / Piston Oil • Rags • Wrench ImPORTANT: Store in a well-ventilated area. If you plan to store in temperatures below 32ºF (0ºC), flush with Wagner Liquid Shield™ (sold separately). 1. Remove the suction tube. Using a wrench, remo...
Page 22 - Troubleshooting
English 22 Troubleshooting Before servicing, always release system pressure by following Pressure Relief Procedure (page 7). Problem A: The sprayer does not start Cause Solution 1. Gas tank is empty Fill the gas tank 2. There is a problem with sprayer engine Call Technical Service Problem B: The spr...
Page 23 - Daily Maintenance
English 23 Problem F: The spray tip assembly leaks Cause Solution 1. The spray tip was assembled incorrectly Check tip assembly and assemble properly see page 19, steps 6-7 2. Gun seal is worn Replace the seal** Problem G: The spray gun will not spray Cause Solution 1. The spray tip plugged Refer to...
Page 24 - Sprayer • Pulvérisateur • Rociador; Parts List • Liste de Pièces • Lista de Piezas
English Français Español 72 1 3 4 2 Sprayer • Pulvérisateur • Rociador Parts List • Liste de Pièces • Lista de Piezas This unit contains no servicable parts. Do not attempt to service yourself. Take the sprayer to a Wagner authorized service center. Cet appareil ne contient aucune pièce nécessitant ...
Page 25 - Español; Français; Suction set • Dispositif d’aspiration • Juego de succión
English Español Français Español 73 4 1 2 3 5 6 7 Suction set • Dispositif d’aspiration • Juego de succión Parts List • Liste de Pièces • Lista de Piezas Item Art. Art. Part No. No de piéce Pieza No. English - Description Français - Description Español - Descripción qty. qté. Cant. 1 0516127 Suction...
Page 27 - Accessories • Accessoires • Accesorios
English Español Français Español 75 Accessories • Accessoires • Accesorios Part No. No de piéce Pieza No. English - Description Français - Description Español - Descripción 0512178A Piston repair kit Jeu de joints pour tronçon d’acheminement Juego de reparación del pistón 0093896 Hose connector kit ...
