Vintec VIN40SG2ERH - User Manual

Page 3 - BEFORE LOADING & PLUGGING IN THE WINE CELLAR

3 It is hazardous for anyone other than an Authorised Service Person to carry out servicing or repairs to this appliance. In Queensland the authorized person must hold a Gas Work Authorisation for hydrocarbon refrigerants, before carrying out servicing or repairs which involve the removal of covers....

Page 4 - Grounding instructions; Wine cellar must be leveled BEFORE loading your wines.; VINTEC

4 Notes: - V30 models are for free standing ONLY: - V40 models are built-in type as per the drawings thereafter; - V50 models are partially built-in, MUST allow 1cm to, side & back clearance. The wine cellar should be placed where the ambient temperature is between 5ºC to 35ºC. If the ambient te...

Page 5 - TURNING ON YOUR WINE CELLAR; Plug in and switch on the cellar by pressing on the power button

5 IMPORTANT - THIS SPACER MUST BE ATTACHED TO THE UNIT BEFORE INSTALLATION FOR VENTILATION PURPOSE. FAILURE TO DO SO VOIDS THE WARRANTY TURNING ON YOUR WINE CELLAR Plug in and switch on the cellar by pressing on the power button for a few seconds. When you use the wine cellar for the first time (or ...

Page 6 - Operating Noises; To reach the desired temperature settings,; wine cellars, like all wine cellars; LOADING YOUR WINE CELLAR; circulation

6 Operating Noises To reach the desired temperature settings, VINTEC wine cellars, like all wine cellars operating with compressors and fans, may produce the following types of noises. These noises are normal and occur as follows: - Gurgling sound, caused by the refrigerant flowing through the appli...

Page 7 - wine storage; , at a constant recommended temperature; recommends; Two Temperature Serving Wine Cellars:; The lower chamber; red wines

7 TYPES OF REGULATION Please note that depending on the loading and settings chosen it takes 24hours for the wine cellar to see the temperature stabilizing. During this time LED seems to move erratically in particular for 2e models. It is a normal process. This process occurs whenever the setting is...

Page 9 - To modify the pre-set temperature of standard models:; Control panel of V30SG e wine cellars; To modify the pre-set temperature of V30SGe models; To modify the pre-set temperature of 40/50SGe and 40/50DG 2e models

9 To modify the pre-set temperature of standard models: Circumrotate the knob, The knob mark is the temperature pre-set area. A clockwise turn sets a lower temperature, An anti clockwise turn sets a higher temperature. Electronic models: V30 “e” model The “TEMP. SET LED, displays the set temperature...

Page 10 - Control panel of SG “2e “model wine cellars

10 To visualize the “set” temperature, press and hold the UP or DOWN buttons, the “set” temperature will temporarily “flash” in the LED display for 5 seconds. SG“2e” models: V30SG"2e", V40SG"2e", V50SG"2e" The “UPPER CHAMBER LCD” displays the upper chamber internal air temper...

Page 14 - While holding the door firmly

14 1 Rubber cover 2 Screw 3 Decorative cover 4 & 7 Screw 5 Top hinge module 6 Door 8 Lower hinge module-Left 9 Cabinet’s leg-short - Pull out the screw covers and unscrew the decorative cover. (Fig.1) - While holding the door firmly , loosen and remove the top hinge, lift up and remove the door ...

Page 15 - While holding the door firmly,

15 V40 models (30mm recess plinth) 1 Lock screws 2 Lower hinge (Right) 3 Door axis 4 Top hinge (Right) 5 Door 6 Cabinet body 7 Top hinge (Left) 8 Lower hinge (Left) - Unscrew the lock screws (1); (Fig. 1) to remove the door axis located at the bottom. - While holding the door firmly, pull the door (...

Page 16 - While holding the door firmly,; remove the three lock screws (2) from the lower

16 - Fix the left top hinge and the bottom left hinge with the bolts as per Fig. 4, - Re-install the door the same way it was removed and fix back the door axis. V40 models (85mm recess plinth) 1 Lower hinge (Right) 2 Lock screws 3 Top hinge (Right) 4 Lock Screws 5 Top hinge (Left) 6 Lower hinge (Le...

Page 17 - While holding the door; take it out

17 V50 models 1 Lock screws 2 Lower hinge (Right) 3 Door axis 4 Top hinge (Right) 5 Door 6 Cabinet body 7 Top hinge (Left) 8 Lower hinge (Left) - Remove the lock screws to untied the door axis at the bottom of the door (Fig 1) - While holding the door firmly, pull the door (5) outward ， take it out ...

Page 21 - considered as null and void.

21 Dimensional drawings: OPERATION ANOMALIES Ensure that there is power to the electrical supply plug by connecting another electrical appliance to it. Check fuse, if any. Make sure that the door is closed properly. If your wine cellar appears to be malfunctioning, unplug it and contact your VINTEC’...

Vintec VIN40SG2ERH - User Manual

Table of Contents:

Summary

Other Vintec Refrigerators Models