Vintec V190BVCBKLH - User Manual

Page 3 - BEFORE LOADING & PLUGGING IN THE WINE CELLAR

3 • The room for installing the appliance must be at least 1 cubic metre per 8 grams of refrigerant. The refrigerant quantity contained in this appliance is listed above in grams; it is also noted on the Rating Plate of the appliance. It is hazardous for anyone other than an Authorised Service Perso...

Page 4 - Grounding instructions; Wine cellar must be leveled BEFORE loading your wines.; VINTEC

4 Notes: - V30 models are for free standing ONLY: - V40 models are built-in type as per the drawings thereafter; - V50 models are partially built-in, MUST allow 1cm to, side & back clearance. The wine cellar should be placed where the ambient temperature is between 5ºC to 35ºC. If the ambient te...

Page 5 - TURNING ON YOUR WINE CELLAR; Plug in and switch on the cellar by pressing on the power button

5 Compressor run appliances require proper ventilation for proper and longer usage. Your Vintec wine cellar is supplied with a back spacer. Affixed the back spacer at the back of the cellar for air circulation and heat evacuation. IMPORTANT - THIS SPACER MUST BE ATTACHED TO THE UNIT BEFORE INSTALLAT...

Page 6 - To reach the desired temperature settings,; wine cellars, like all wine cellars

6 Important: If the unit is unplugged, power is lost, or turned off, wait 3 to 5 minutes before restarting the unit. The wine cellar will not start if you attempt to restart before this time delay. Operating Noises To reach the desired temperature settings, VINTEC wine cellars, like all wine cellars...

Page 7 - of the wine cellar and cause back injury.; wine storage; , at a constant recommended temperature; recommends; Two Temperature Serving Wine Cellars:; The lower chamber; red wines

7 - Do not cover the wooden shelves with alloy foil or other materials, as it will obstruct air circulation. - Do not move your wine cellar while it is loaded with wines. This might distort the body of the wine cellar and cause back injury. TYPES OF REGULATION Please note that depending on the loadi...

Page 9 - MIN; ” adjustable from 15 to 18 oC; To modify the pre-set temperature of standard models:; Control panel of V30SG e wine cellars; To modify the pre-set temperature of V30SGe models; Control panel of SG e and DG “2e “model wine cellars; To modify the pre-set temperature of 40/50SGe and 40/50DG 2e models

9 “ MIN ” adjustable from 15 to 18 ºC To modify the pre-set temperature of standard models: Circumrotate the knob, The knob mark is the temperature pre-set area. A clockwise turn sets a lower temperature, An anti clockwise turn sets a higher temperature. Electronic models: V30 “e” model The “TEMP. S...

Page 10 - Control panel of SG “2e “model wine cellars

10 Adjust the desired cooling temperature by pressing the UP or DOWN buttons. Each depression of the buttons will scroll through the available temperature settings in increments of 1 degree Celsius. The temperature setting can be adjusted from 5 to 18 To visualize the “set” temperature, press and ho...

Page 14 - While holding the door firmly

14 1 Rubber cover 2 Screw 3 Decorative cover 4 & 7 Screw 5 Top hinge module 6 Door 8 Lower hinge module-Left 9 Cabinet’s leg-short - Pull out the screw covers and unscrew the decorative cover. (Fig.1) - While holding the door firmly , loosen and remove the top hinge, lift up and remove the door ...

Page 15 - While holding the door firmly,

15 V40 models (30mm recess plinth) 1 Lock screws 2 Lower hinge (Right) 3 Door axis 4 Top hinge (Right) 5 Door 6 Cabinet body 7 Top hinge (Left) 8 Lower hinge (Left) - Unscrew the lock screws (1); (Fig. 1) to remove the door axis located at the bottom. - While holding the door firmly, pull the door (...

Page 16 - remove the three lock screws (2) from the lower

16 - Fix the left top hinge and the bottom left hinge with the bolts as per Fig. 4, - Re-install the door the same way it was removed and fix back the door axis. V40 models (85mm recess plinth) 1 Lower hinge (Right) 2 Lock screws 3 Top hinge (Right) 4 Lock Screws 5 Top hinge (Left) 6 Lower hinge (Le...

Page 17 - While holding the door; take it out

17 V50 models 1 Lock screws 2 Lower hinge (Right) 3 Door axis 4 Top hinge (Right) 5 Door 6 Cabinet body 7 Top hinge (Left) 8 Lower hinge (Left) - Remove the lock screws to untied the door axis at the bottom of the door (Fig 1) - While holding the door firmly, pull the door (5) outward ， take it out ...

Page 18 - V30 models are free standing only. Any built in voids the warranty; V40’s Installation instructions (85mm recess plinth)

18 INSTALLATION INSTRUCTIONS AND DRAWINGS FOR BUILT IN PURPOSES V30 models are free standing only. Any built in voids the warranty V40’s Installation instructions (85mm recess plinth) 1. Wine Cabinet dimensions : Height 820mm – 860mm (40mm adjustable feet) Width 595mm Depth 571mm 2. This wine cabine...

Page 21 - considered as null and void.

21 Dimensional drawings: OPERATION ANOMALIES Ensure that there is power to the electrical supply plug by connecting another electrical appliance to it. Check fuse, if any. Make sure that the door is closed properly. If your wine cellar appears to be malfunctioning, unplug it and contact your VINTEC’...

Vintec V190BVCBKLH - User Manual

Table of Contents:

Summary

Other Vintec Refrigerators Models