VEVOR WDPQSWDKZQY404HTNV1 - User Manual

Page 3 - Solar Roof Exhaust Fan

- 1 - JBSF-320G <Picture Only For Reference> Have product questions? Need technical support? Please feel free tocontact us: [email protected] NEED HELP? CONTACT US! This is the original instruction, please read all manual instructions carefully before operating. VEVOR reserves a clear interpre...

Page 4 - Contents; . Product Description; WARNING; Indicates a hazardous situation; CAUTION; Indicates a hazardous situation which, if not avoided,; Save all warnings and instructions for future reference.

- 2 - Contents Ⅰ . Safety Precautions Ⅱ . Product Description Ⅲ . Installation Guide Ⅳ . Function Description Ⅴ . Faults and Maintenance Ⅰ .Safety Precautions WARNING Indicates a hazardous situation that, if not avoided, could result in death or serious injury. DANGER Indicates a hazardous situation...

Page 6 - Its design includes the following features:

- 4 - Solar roof exhaust fan functions in several ways to keep your place cool and comfortable. Its design includes the following features: • It keeps your home cooler in the summer by extracting 20 times more air than a Whirly Bird.• It is solar-powered, so there is no running cost.• It reduces the...

Page 7 - TECHNICAL PARAMETER; Monocrystalline PV, Heavy Duty Frame, 3mm Tempered Glass

- 5 - TECHNICAL PARAMETER Model JBSF-320G Motor DC 15V 40W Solar Panel Type Monocrystalline PV, Heavy Duty Frame, 3mm Tempered Glass Solar Panel Output 40Watts, 15 VDC Fan 300mm Balanced Blade (×5), with Low Resistance Inverter Voltage AC 100~240V 50 / 60Hz Ⅲ .Installation Guide

Page 8 - I. METAL ROOF INSTALLATION; GUIDE; x solar fan up to 1,000 sqft place

- 6 - Please read this installation guide carefully to install the solar roof exhaust fan. Depending on theroof type, you may follow installation steps for the best result. Please make sure the work area isdry before installing. Do not install during or after rain. I. Metal Roof II. Tile Roof I. MET...

Page 10 - Don’t apply silicone to the valleys at the bottom of the flashing.

- 8 - Note: Take care not to cut into any battens/rafters under the roof sheet when cutting. STEP 4 Slide the flashing back up under the roof capping, refit the 2 ridge capping screws through theflashing, and bend the edges of the flashing down on the left and right sides to create a tight fitwith t...

Page 15 - Ensure you discard this removed tile. Do not leave it on the roof.

- 13 - Ensure you discard this removed tile. Do not leave it on the roof. STEP 3 Lift the tiles above the tile opening, slide the flashing into place as shown here, and then push thetiles back down. This will mold the flashing to the tiles. STEP 4 Fit a minimum of one rafter/batten strap (2 are supp...

Page 16 - roof directly under the tiles.

- 14 - Note: Rafters run from the top of the roof down to the facial and battens run across the roof directly under the tiles. STEP 5 Once the flashing fitting is complete, run a bead of clear silicone along the top of theflashing that joins with the upper tiles. STEP 6 Place the main body of the fa...

Page 17 - best suit the sun in warmer months.

- 15 - Tip: Position the solar panel between the south (north for the southern hemisphere) and west to best suit the sun in warmer months. STEP 7 As shown in the figure, using a powered screw-driver, screw at least 4 small tech screws throughthe pre-drilled holes in the fan's main body through into ...

Page 18 - Manufacturer; Foshan Shunde JustBrisk Technology Co.,Ltd; Address

- 16 - STEP 8 You can now adjust the angle of the solar panel to receive maximum sun especially during themidday of the warmer months as shown in the figure. As the pitch of many roofs is already at agood angle for the summer sun, you may just be able to leave the panel in the down position as itis ...

VEVOR WDPQSWDKZQY404HTNV1 - User Manual

Table of Contents:

Summary

Other VEVOR Fans Models