Trinity TRI64-64N05T - User Manual

Control Panel Product Information The microcomputer ceramic hob can meet different kinds of cuisine demandsbecause of resistance wire heating, micro-computerized control and multi-powerselection, really the optimal choice for modern families.The ceramic hob centers on customers and adopts personaliz...

Make sure that the base of your pan is smooth, sits flat against the glass, and isthe same size as the cooking zone. Always centre your pan on the cooking zone. Always lift pans off the ceramic hob – do not slide, or they may scratch the glass. Using your Induction Hob To start cooking 1. Touch the ...

3. Touching the heating zone selection control ,and a indicator next to the key will flash 。 4. Select a heat setting by touching the “-“ or “+” control.• If you don’t choose a heat setting within 1 minute, the Induction hob will automaticallyswitch off. You will need to start again atstep 1. • You ...

2. Turn the cooking zone off by scrolling down to”0” or touching”-“ and”+” control together. Make sure the display shows”0” 3. Turn the whole cooktop off by touching the ON/OFF control. 4. Beware of hot surfaces H will show which cooking zone is hot to touch. It will disappear when the surface has c...

To unlock the controls 1. Make sure the induction hob is turned on.2. Touch and hold the “—” and “ + ” control for a while. 3. You can now start using your induction hob. When the hob is in the lock mode,all the controls are disable except theON/OFF , you can always turn the induction hob off with t...

Using the Timer You can use the timer in two different ways:• You can use it as a minute minder. In this case, the timer will not turn any cooking zone off when the set time is up. • You can set it to turn one or more cooking zones off after the set time is up.• You can set the timer up to 99 minute...

5. set the time by touching the ”-“ or ”+” control (e.g.9), now the timer you set is 95 minutes. 6. When the time is set, it will begin to count down immediately. The display will show the remainingtime. 7. Buzzer will bips for 30 seconds and the timer indicator shows “- - “ when the setting timefin...

1. When you set the time for several cooking zones simultaneously, decimal dots of the relevant cooking zones are on. The minute display shows the min. timer.The dot of the corresponding zone flashes. 2. Once the countdown timer expires, the corresponding zone will switch off. Then it will show the ...

Cooking Guidelines Cooking Tips • When food comes to the boil, reduce the power setting.• Using a lid will reduce cooking times and save energy by retaining the heat.• Minimise the amount of liquid or fat to reduce cooking times.• Start cooking on a high setting and reduce the setting when the food ...

5. Stir-fry the vegetables. When they are hot but still crisp, turn the cooking zone to a lower setting, return the meat to the pan and add your sauce. 6. Stir the ingredients gently to make sure they are heated through.7. Serve immediately. Heat Settings The settings below are guidelines only. The ...

Care and Cleaning What? How? Important! Everyday soiling onglass (fingerprints, marks, stains left by food or non-sugaryspillovers on the glass) 1. Switch the power to the cooktop off. 2. Apply a cooktop cleaner while the glass is still warm(but not hot!) 3. Rinse and wipe dry with a clean cloth or ...

Hints and Tips Problem Possible causes What to do The induction hob cannot be turned on. No power. Make sure the induction hob is connected to the power supplyand that it is switched on. Check whether there is a power outage in your home or area. Ifyou’ve checked everything and the problem persists,...

The induction hob or a cooking zone hasturned itself off unexpectedly, a tone sounds and an errorcode is displayed (typically alternating with one or two digitsin the cooking timer display). Technical fault. Please note down the error letters and numbers, switchthe power to the induction hob off at ...

Technical Specification Cooking Hob TRI64-64N05T Cooking Zones 4 Zones Supply Voltage 220-240V~ /380-415V 2N~ Installed Electric Power 6400W Product Size L×W×H(mm) 590 × 520 × 66 Building-in Dimensions A×B (mm) 560 × 490 Weight and Dimensions are approximate. Because we continually strive toimprove ...

Installation Selection of installation equipment Cut out the work surface according to the sizes shown in the drawing.For the purpose of installation and use, a minimum of 5 cm space shall bepreserved around the hole.Be sure the thickness of the work surface is at least 30mm. Please selectheat-resis...

A(mm) B(mm) C(mm) D E 760 50 mini 20 mini Air intake Air exit 5mm Before you install the hob, make sure that • the work surface is square and level, and no structural members interfere with space requirements • the work surface is made of a heat-resistant material• if the hob is installed above an o...

• there is adequate flow of fresh air from outside the cabinetry to the base of the hob • if the hob is installed above a drawer or cupboard space, a thermal protection barrier is installed below the base of the hob • the isolating switch is easily accessible by the customer When you have installed ...

2 7 The power supply should be connected in compliance with the relevantstandard,or a single-pole circuit breaker.the method of connection is shownbelow. Cautions 1. The induction hotplate must be installed by qualified personnel or technicians. We have professionals at your service. Please never co...