Texas Instruments ADS5411 - Manual

1.1 Purpose 1.2 EVM Basic Functions 1.3 Power Requirements 1.3.1 Voltage Limits 1.4 EVM Operational Procedure Chapter 1 SLWU020B – February 2005 – Revised February 2006 Overview This User’s Guide document gives a general overview of the ADS5423/24/33 and ADS5411 evaluationmodule (EVM) and provides a...

www.ti.com * dBFS + 20 log captured max code * captured min code 2 N , where N is the number of bits. EVM Operational Procedure Table 1-1. Three Pin Jumper List Table JUMPER FUNCTION LOCATION: PINS 1–2 LOCATION: PINS 2–3 DEFAULT SJP3 Provides AIN+ source to ADC Source provided from T2 Source provide...

2.1 Schematic Diagram 2.2 Circuit Function 2.2.1 Analog Inputs 2.2.2 Power 2.2.3 Outputs Chapter 2 SLWU020B – February 2005 – Revised February 2006 Circuit Description The schematic diagram for the EVM is attached at the end of this document. The following paragraphs describe the function of EVM cir...

www.ti.com Circuit Function Table 2-1. Output Connector J9 J9 PIN DESCRIPTION J9 PIN DESCRIPTION 1 CLK 21 DATA BIT 6 2 GND 22 GND 3 NC 23 DATA BIT 7 4 GND 24 GND 5 NC 25 DATA BIT 8 6 GND 26 GND 7 NC 27 DATA BIT 9 8 GND 28 GND 9 DATA BIT 0 (LSB) 29 DATA BIT 10 10 GND 30 GND 11 DATA BIT 1 31 DATA BIT ...

Chapter 3 SLWU020B – February 2005 – Revised February 2006 Parts List Table 3-1 lists the parts used in constructing the EVM Table 3-1. Bill of Materials for EVM VALUE QTY PART NUMBER VENDOR REF DES NOT INSTALLED CAPACITORS 0.1 µ F, 25 V, +80/–20% 4 ECJ-0EF1E104Z Panasonic C1, C2, C3, C4 Capacitor 0...

4.1 PCB Layout Chapter 4 SLWU020B – February 2005 – Revised February 2006 Physical Description This chapter describes the physical characteristics and PCB layout of the EVM and lists the componentsused on the module. The EVM is constructed on a 6-layer, 4.77-inch × 3.4-inch, 0.062-inch thick PCB usi...

www.ti.com 4.2 Schematics Schematics SLWU020B – February 2005 – Revised February 2006 Physical Description 17 Submit Documentation Feedback

1 2 3 4 5 6 A B C D 6 5 4 3 2 1 D C B A FILE: Drawn By: Engineer: ti 12500 TI Boulevard. Dallas, Texas 75243 Title: SHEET: OF: SIZE: DATE: REV: 8-Dec-2004 DOCUMENTCONTROL # ADS5424 A 1 J. SETONY. DEWONCK NOTE 1. DO NOT INSTALL 1 2 3 4 5 J5 SMA_PCB_MT_MOD C1 .1uF C2 .1uF CLK+ CLK- CLK+ CLK- R449.9 C4...

www.ti.com Schematics EVALUATION BOARD/KIT IMPORTANT NOTICE Texas Instruments (TI) provides the enclosed product(s) under the following conditions: This evaluation board/kit is intended for use for ENGINEERING DEVELOPMENT,DEMONSTRATION, OR EVALUATION PURPOSES ONLY and is not considered by TI to be a...

www.ti.com Schematics FCC Warning This evaluation board/kit is intended for use for ENGINEERING DEVELOPMENT,DEMONSTRATION, OR EVALUATION PURPOSES ONLY and is not considered by TI to be afinished end-product fit for general consumer use. It generates, uses, and can radiate radiofrequency energy and h...

IMPORTANT NOTICE Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, modifications, enhancements,improvements, and other changes to its products and services at any time and to discontinue any product or service without notice.Customers should obtain the l...