Texas Instruments TSC2007EVM-PDK - Manual
Texas Instruments TSC2007EVM-PDK – Manual, read for free online in PDF format. We hope this helps you resolve any issues you may have. If you have further questions, please contact us through the contact form.
Table of Contents:
- Page 2 – Features; Analog Interface; EVM Overview; Table 2. Analog Interface Pinout; PIN NUMBER
- Page 3 – TSC Power; Digital Interface; Table 3. Digital Interface Pinout; Table 4; Table 4. Power Supply Pinout
- Page 4 – Analog Input; EVM Operation; CAUTION; USB
- Page 5 – TSC2007EVM-PDK Block Diagram; Kit Operation; Table 6. List of Jumpers; JUMPER; A block diagram of the TSC2007EVM-PDK is shown in
- Page 6 – microcontroller; Quick Start
- Page 7 – Accept the license agreement, and continue the installation.; Figure 2. Default Software Screen
- Page 8 – Touch Screen Functions Panel; Figure 1
- Page 9 – Datalogging; EVM Bill of Materials; When ready to begin recording data to a file, select Datalogging; Table 7. TSC2007EVM Bill of Materials; Reference Designator
- Page 11 – The schematic diagram is provided as a reference.
- Page 12 – ti
- Page 16 – IMPORTANT NOTICE; Products
User's Guide
SLAU199 – March 2007
TSC2007EVM and TSC2007EVM-PDK User's Guide
This
user's
guide
describes
the
characteristics,
operation,
and
use
of
the
TSC2007EVM, both by itself and as part of the TSC2007EVM-PDK. This evaluation
module (EVM) is a 4-wire touch screen controller EVM which also has auxiliary input
and temperature measurement capabilities. A complete circuit description, schematic
diagram, and bill of materials are included.
The following related documents are available through the Texas Instruments Web site
at
Table 1. EVM-Compatible Device Data Sheets
DEVICE
LITERATURE NUMBER
TSC2007
TAS1020B
REG1117-5
TPS767D318
SN74LVC125A
SN74LVC1G125
SN74LVC1G07
Contents
1
EVM Overview
2
Analog Interface
3
Digital Interface
4
Power Supplies
5
EVM Operation
6
Kit Operation
7
EVM Bill of Materials
8
TSC2007EVM Schematic
.................................................................................................
9
USB-MODEVM Schematic
................................................................................................
List of Figures
1
TSC2007EVM-PDK Block Diagram
......................................................................................
2
Default Software Screen
...................................................................................................
List of Tables
1
EVM-Compatible Device Data Sheets
....................................................................................
2
Analog Interface Pinout
3
Digital Interface Pinout
4
Power Supply Pinout
5
Power Selection Options - JMP1
..........................................................................................
6
List of Jumpers
7
TSC2007EVM Bill of Materials
.............................................................................................
8
USB-MODEVM Bill of Materials
..........................................................................................
SLAU199 – March 2007
TSC2007EVM and TSC2007EVM-PDK User's Guide
1
"Loading the manual" means you need to wait until the file loads and becomes available for online reading. Some manuals are very large, and the time they take to appear depends on your internet speed.
Summary
www.ti.com 1 EVM Overview 1.1 Features 1.2 Introduction 2 Analog Interface EVM Overview • Full-featured evaluation board for the TSC2007 4-wire resistive touch screen controller (TSC). • Modular design for use with a variety of DSP and microcontroller interface boards. The TSC2007EVM-PDK is a comple...
www.ti.com 3 Digital Interface 4 Power Supplies 4.1 TSC Power Digital Interface The TSC2007EVM is designed to easily interface with multiple control platforms. Samtec part numbersSSW-110-22-F-D-VS-K and TSM-110-01-T-DV-P provide a convenient 10-pin, dual-row header/socketcombination at J2. This head...
www.ti.com 4.2 Stand-Alone Operation 4.3 USB-MODEVM Interface Power 5 EVM Operation 5.1 Analog Input 5.2 Digital Control 5.3 Default Jumper Locations EVM Operation When used as a stand-alone EVM, power can be applied to TP1, referenced to TP3. CAUTION Verify that all power supplies are within the sa...
