Texas Instruments TSC2007EVM-PDK - Manuals

Page 2 - Features; Analog Interface; EVM Overview; Table 2. Analog Interface Pinout; PIN NUMBER

www.ti.com 1 EVM Overview 1.1 Features 1.2 Introduction 2 Analog Interface EVM Overview • Full-featured evaluation board for the TSC2007 4-wire resistive touch screen controller (TSC). • Modular design for use with a variety of DSP and microcontroller interface boards. The TSC2007EVM-PDK is a comple...

Page 3 - TSC Power; Digital Interface; Table 3. Digital Interface Pinout; Table 4; Table 4. Power Supply Pinout

www.ti.com 3 Digital Interface 4 Power Supplies 4.1 TSC Power Digital Interface The TSC2007EVM is designed to easily interface with multiple control platforms. Samtec part numbersSSW-110-22-F-D-VS-K and TSM-110-01-T-DV-P provide a convenient 10-pin, dual-row header/socketcombination at J2. This head...

Page 4 - Analog Input; EVM Operation; CAUTION; USB

www.ti.com 4.2 Stand-Alone Operation 4.3 USB-MODEVM Interface Power 5 EVM Operation 5.1 Analog Input 5.2 Digital Control 5.3 Default Jumper Locations EVM Operation When used as a stand-alone EVM, power can be applied to TP1, referenced to TP3. CAUTION Verify that all power supplies are within the sa...

Page 5 - TSC2007EVM-PDK Block Diagram; Kit Operation; Table 6. List of Jumpers; JUMPER; A block diagram of the TSC2007EVM-PDK is shown in

www.ti.com 6 Kit Operation 6.1 TSC2007EVM-PDK Block Diagram Kit Operation Table 6. List of Jumpers JUMPER SHUNT POSITION JUMPER DESCRIPTION JMP1 2-3 Analog power select (default is +3.3VD) JMP2 Closed EEPROM address select. When installed and used with the USB-MODEVM, firmware for themotherboard is ...

Page 6 - microcontroller; Quick Start

www.ti.com TAS1020B USB 8052 microcontroller USB EVM Position 1 EVM Position 2 Control Interface Audio Interface TSC2007EVM TSC2007 SPI, I2C I2S, AC97 X+ X− Y+ Y− AUX SDASCL PENIRQ 6.2 Quick Start Kit Operation Figure 1. TSC2007EVM-PDK Block Diagram The USB-MODEVM interface board is intended to be u...

Page 7 - Accept the license agreement, and continue the installation.; Figure 2. Default Software Screen

www.ti.com Kit Operation Place the CD-ROM into your PC CD-ROM drive. Locate the Setup program on the disk, and run it. TheSetup program will install the TSC2007 Evaluation software on your PC. Accept the license agreement, and continue the installation. When the installation completes, click Finish ...

Page 8 - Touch Screen Functions Panel; Figure 1

www.ti.com 6.3 USB-MODEVM Interface Board 6.4 Program Description 6.4.1 Touch Screen Functions Panel 6.4.2 Data Acquisition Functions Panel 6.4.3 Configuration Panel Kit Operation The simple diagram shown in Figure 1 shows only the basic features of the USB-MODEVM interface board. The board is built...

Page 9 - Datalogging; EVM Bill of Materials; When ready to begin recording data to a file, select Datalogging; Table 7. TSC2007EVM Bill of Materials; Reference Designator

www.ti.com 6.4.4 Datalogging 7 EVM Bill of Materials EVM Bill of Materials The two power-down bits of the TSC2007 can be set from this panel as well. A brief description of themode selected is shown on the screen when setting these bits; see Table 3 (Command Byte Definitions)of the TSC2007 data shee...

Page 11 - The schematic diagram is provided as a reference.

www.ti.com 8 TSC2007EVM Schematic 9 USB-MODEVM Schematic TSC2007EVM Schematic Table 8. USB-MODEVM Bill of Materials (continued) Reference Designator Description Manufacturer Manufacturer's Part Number TP1, TP2, TP3, TP4, TP5, Miniature test point terminal Keystone Electronics 5000 TP6, TP9, TP10, TP...

Page 12 - ti

1 2 3 4 5 6 A B C D 6 5 4 3 2 1 D C B A ti 12500 T.I. Boulevard, Dallas, Texas 75243 USA TITLE SHEET OF FILE SIZE DATE REV 5-Jan-2007 DRAWN BY ENGINEER REVISION HISTORY REV ENGINEERING CHANGE NUMBER APPROVED B DATA ACQUISITION PRODUCTS HIGH-PERFORMANCE ANALOG DIVISION SEMICONDUCTOR GROUP WENDY FANG ...

Page 16 - IMPORTANT NOTICE; Products

IMPORTANT NOTICE Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, modifications, enhancements,improvements, and other changes to its products and services at any time and to discontinue any product or service without notice.Customers should obtain the l...