Page 3 - ii
Rev 0.01 TUP900 Series Specifications Manual ii 5-2 Static Electricity Tolerance (ESD) .........................................................................................................5-2 5-3 AC Line Noise Tolerance ...............................................................................
Page 4 - GENERAL DESCRIPTION; T U P 9
Rev 0.01 TUP900 Series Specifications Manual 1-1 1. GENERAL DESCRIPTION The TUP900 series is a direct line thermal printer capable of high speed printing that employs a thermalline dot printing system and is composed of a unit comprising thermal paper roll storage. This type is used,embedded in elec...
Page 5 - PRINTER CONFIGURATION; -1 Basic Configuration
Rev 0.01 TUP900 Series Specifications Manual 2-1 2. PRINTER CONFIGURATION 2-1 Basic Configuration This unit is composed of modules. The configuration is shown below. TUP992-24/TUP992-24J1 (Thermal line unit printers) Thermal mechanism module (TMP900 Series) Presenter module (PR900 Series) Control bo...
Page 6 - BASIC SPECIFICATIONS; -1 Printing Specifications
Rev 0.01 TUP900 Series Specifications Manual 3-1 3. BASIC SPECIFICATIONS 3-1 Printing Specifications (1) Print Method: Direct Thermal Line Printing (2) Dot Configuration: 832 dots/line (3) Dot Density: 8 dots/mm (203 DPI) (4) Printing Region: Maximum 104 mm (See figure below) Notes 1) The mechanism ...
Page 7 - -2 Character Specifications and Bar Code Specifications; Item
Rev 0.01 TUP900 Series Specifications Manual 3-2 3-2 Character Specifications and Bar Code Specifications 3-2-1 STAR Line Mode Item Contents Standard Specifications Alphanumeric Characters 95 Characters Expanded Graphics 128 Characters International Characters 32 Characters Alphanumeric Characters 9...
Page 9 - -3 Paper Specifications
Rev 0.01 TUP900 Series Specifications Manual 3-4 3-3 Paper Specifications 3-3-1 Thermal Paper roll (1) Paper Width: 79.5 ±0.5 mm to 111.5 ±0.5 mm(Rolled Dimensions: 80 +0.5/-1 to 112 +0.5/-1 mm) (2) Paper Thickness: 65 to 150 µm (3) Paper roll Outer Diameter: Maximum φ 150 mm Note 1) Use of optional...
Page 11 - (7) Weight Shaft and Loop Guide on the Presenter Module
Rev 0.01 TUP900 Series Specifications Manual 3-6 (7) Weight Shaft and Loop Guide on the Presenter Module The TUP900 Series printers require the accessory weight shaft and loop guide for the thickness of thepaper to be used to ensure the smooth feeding of paper.See the table below for the optimum mec...
Page 12 - Black mark pitch can be set to a dimension of A = 75 to 300 mm.
Rev 0.01 TUP900 Series Specifications Manual 3-7 3-3-2 Black Mark Specifications The following describes the recommended black mark specifications for printers that use the paper outsensor as the black mark sensor. (1) Black Mark Pitch (Dimension A) Black mark pitch can be set to a dimension of A = ...
Page 13 - So, you must set for plenty of top margin.
Rev 0.01 TUP900 Series Specifications Manual 3-8 (4) Top Margin (Dimension B) Set the printing range, leaving plenty of top margin from the cutting position.When not reversing paper feed, a top margin with a minimum total of 19 mm is recommended with thedistance of 15 mm from the thermal head heatin...
Page 14 - -4 Thermal Mechanism Module
Rev 0.01 TUP900 Series Specifications Manual 3-9 3-4 Thermal Mechanism Module 3-4-1 Thermal Head (1) Thermal Element Configuration: 2 elements/dot (2) Number of Thermal Elements: 832 dots (3) Thermal Element Scanning Density: 0.125 mm/dot (8 dots/mm) (4) Average Resistance Value: 800 Ω ±3% (initial ...
Page 15 - Friction Method
Rev 0.01 TUP900 Series Specifications Manual 3-10 3-5 Presenter Module 3-5-1 Feed Rollers (1) Feed Method: Friction Method (2) Paper Feed Speed: 300 mm/s Note 1) Paper feed speed varies according to the ambient environment and the thickness of the paper used. 3-5-2 Paper Feed Motor (1) Format: DC Br...
Page 16 - -6 Paper Roll Supply Module
Rev 0.01 TUP900 Series Specifications Manual 3-11 3-6 Paper Roll Supply Module 3-6-1 Paper Roll Holder (1) Paper roll Support Method: Shaft Support Method Using the Paper roll Holder (Fixed Shaft Unit) (2) Paper Tube: Inner Diameter φ 1 Inch Paper Tube ( φ 25.4 ±1 mm) Inner Diameter φ 2 Inch Paper T...
Page 17 - -7 Reliability Specifications
Rev 0.01 TUP900 Series Specifications Manual 3-12 3-7 Reliability Specifications 3-7-1 Thermal Mechanism Module (1) Life: 15 million lines (2) MCBF: 37 million lines Note 1) If the recommended paper is not used, the life of the printer cannot be guaranteed. Always use the recommended paper types. 3-...
Page 18 - EXTERNAL SPECIFICATIONS; -1 External Specifications; Feeds and discharges paper
Rev 0.01 TUP900 Series Specifications Manual 4-1 4. EXTERNAL SPECIFICATIONS 4-1 External Specifications 4-1-1 External Dimensions TUP992-24/TUP992-24J1: Width: 192 mm × Depth: 249.3 mm × Height: 179 mm Note 1) These dimensions do not include paper roll or optional parts. 4-1-2 External Drawings See ...
Page 20 - ENVIRONMENT SPECIFICATIONS; -1 Temperature and Humidity; high temperatures and humidity.
Rev 0.01 TUP900 Series Specifications Manual 5-1 5. ENVIRONMENT SPECIFICATIONS 5-1 Temperature and Humidity 5-1-1 When Operating (1) Temperature: 0 to 50°CHowever, printing is guaranteed at 5 to 50°C (2) Humidity: 10 to 80% RHHowever, there must be no condensation. Assumes 80% RH at 34°C Note 1) Whe...
Page 21 - -3 AC Line Noise Tolerance
Rev 0.01 TUP900 Series Specifications Manual 5-2 5-2 Static Electricity Tolerance (ESD) Direct Electrical Discharge: Contact discharge ±6 kV (individual unit) Air discharge ±8 kV (individual unit) Indirect Discharge: ±6 kV (individual unit) ±4 kV (Checker connection) Note) When using the optional po...
Page 22 - CE
Rev 0.01 TUP900 Series Specifications Manual 6-1 6. SAFETY 6-1 Standard CE Marking EMC Instruction CE Marking CE Marking Low voltage instruction FCC Class A VCCI Class A EMI Standard EN55022 Class B Note 1) When using the optional power adapter (PS60L – 24A). Federal Communications Commission Radio ...
Page 23 - -1 Control Board Layout
Rev 0.01 TUP900 Series Specifications Manual 7-1 7. USAGE EXAMPLE (LAYOUT EXAMPLE) 7-1 Control Board Layout This unit is mounted with the control board (PCB chassis) shown in Fig. 4.1.2 at the time of shipment. It ispossible, however, to change the position of the control board according to the cond...
Page 29 - SETTING UP THE PRINTER UNIT; -1 Mounting the Units
Rev 0.01 TUP900 Series Specifications Manual 8-1 8. SETTING UP THE PRINTER UNIT 8-1 Mounting the Units 8-1-1 Mounting the Printer Unit Use the four holes a, b, c and d shown in the external drawing of Fig. 4.1.2 on the separate sheet to fastenthe printer unit.Also, it is recommended the unit be fast...
Page 30 - -3 Adjusting the Paper roll Holder Unit; Paper roll Holder Types
Rev 0.01 TUP900 Series Specifications Manual 8-2 8-3 Adjusting the Paper roll Holder Unit It is necessary to adjust the paper roll holder for the width of the paper you use.If the setting position is incorrect, the paper roll will be supplied improperly to the mechanism which in turncauses paper tra...
Page 32 - -4 Mounting the Friction Spring; us for details on fine adjustments.
Rev 0.01 TUP900 Series Specifications Manual 8-4 8-4 Mounting the Friction Spring It is necessary to adjust the friction spring position for the width of the paper you intend to use.If the setting position is incorrect, the paper roll will be supplied improperly to the mechanism which in turncauses ...
Page 33 - A B C; Reference a; Boss
Rev 0.01 ries Specifications Manual 8-5 Fig. 8.4.1.C Touch to boss. Touch to boss. Fig. 8.4.1.A A B C C' B' A' TUP900 Se A 82.5 82.5 112 112 82.5 82.5 112 112 112 112 82.5 82.5 Fig. 8.4.1.A lign notch with reference center. Align notch with reference center. Reference a' Reference a Boss 2 (Pitch) 2...
Page 36 - -5 Adjusting the Near End Sensor; -5-2 Adjusting to the Paper roll Diameter Direction
Rev 0.01 TUP900 Series Specifications Manual 8-8 8-5 Adjusting the Near End Sensor It is necessary to adjust the near end sensor to detect the remaining amount of paper roll. To adjust theposition of the near end sensor, adjust the roll diameter direction that determines the adjustment of thepaper w...
Page 37 - When using a
Rev 0.01 TUP900 Series Specifications Manual 8-9 (2) Optional High Volume Paper Roll Supply (RHU-T900) The method to adjust the near end sensor when using the optional high volume paper roll supply, isbasically the same as that used for the printer unit.However, be aware that the difference in the s...
Page 40 - HANDLING THE PRINTER UNIT; -1 Precautions Regarding Designs; Plated steel is used so rusting can occur on edges.; -2 Precautions for Handling; Avoid leaving the printer without paper.
Rev 0.01 TUP900 Series Specifications Manual 9-1 9. HANDLING THE PRINTER UNIT 9-1 Precautions Regarding Designs 1. If the positional relationship of the printer unit and the paper roll holder mounting is poor, paper canskew, the ends of the paper become creased or the paper jam. For that reason, be ...
Page 41 - that the power has been turned OFF before starting your work.; -3 Precautions Concerning Safety; Do not disassemble or modify the units.
Rev 0.01 TUP900 Series Specifications Manual 9-2 18. This unit is provided with an auto-cutter as standard equipment, but absolutely never approach the auto-cutter blades while the cutter is operating because it is extremely dangerous. Also, if the cutterstops, absolutely never touch the blades dire...
Page 42 - -4 How to Set the Paper roll; Set the paper roll as shown in the following procedures.
Rev 0.01 TUP900 Series Specifications Manual 9-3 9-4 How to Set the Paper roll Set the paper roll as shown in the following procedures. Procedure 1. Open the frame for fastening the mechanism (mechanism and presenter).Hold the unit holder, as shown in Fig. 9.4 A, and open the frame for fastening t...
Page 45 - Damper rollers
Rev 0.01 s Manual 9-6 Fig.9.4.F TUP900 Series Specification Fig.9.4.E Damper rollers Paper inlet Paper guide
Page 46 - -5 Performing Maintenance; -5-1 Cleaning the Thermal Head and Platen; Remove the right and left lock levers.
Rev 0.01 TUP900 Series Specifications Manual 9-7 9-5 Performing Maintenance 9-5-1 Cleaning the Thermal Head and Platen To ensure long-term and stable printing, periodically clean the thermal head and the platen. It isrecommended that you clean every 500,000 lines.The thermal head and platen can be c...
Page 47 - Knob
Rev 0.01 s Manual 9-8 Fig.9.5.2. Knob Release lever Lock lever TUP900 Series Specification
