Stanley SPL31A-S - Manual

SPL31 User Manual ◄ 5 Tool operators and maintenance personnel must always comply with the safety precautions given in this manual and on the stickers and tags attached to the tool and hose.These safety precautions are given for your safety. Re- view them carefully before operating the tool and befo...

SPL31 User Manual ◄ 7 The rated working pressure of the hydraulic hose must be equal to or higher than the relief valve setting on the hy- draulic system. There are three types of hydraulic hose that meet this requirement and are authorized for use with Stanley Hydraulic Tools. They are: Certified n...

8 ► SPL31 User Manual Oil Flow Hose Lengths Inside Diameter USE ( Press/Return) Min. W orking Pressure GPM LPM FEET METERS INCH MM PSI BAR Certified Non-Conductive Hose - Fiber Braid - for Utility Bucket T rucks 4-9 15-34 up to 10 up to 3 3/8 10 Both 2250 155 Conductive Hose - W ire Braid or Fiber B...

SPL31 User Manual ◄ 9 Flow Range Nominal Operating Pressure (at the power supply outlet) System relief valve setting (at the power supply outlet) Maximum back pressure (at tool end of the return hose) Measured at a max. fluid viscosity of: (at min. operating temperature) Temperature: Sufficient heat...

10 ► SPL31 User Manual CHECK HYDRAULIC POWER SOURCE 1. Using a calibrated flowmeter and pressure gauge, check that the hydraulic power source develops a flow of 5-10.5 gpm/15-40 lpm at 2000 psi/140 bar.2. Make certain the hydraulic power source is equipped with a relief valve set to a max of 2500 ps...

SPL31 User Manual ◄ 11 Problem Cause Solution Spike puller does not cycle. Hydraulic power source not functioning correctly. Check power source for proper flow and pressure (5-10 gpm/19-34 lpm, 2500 psi/172 bar. Coupler or hoses blocked. Remove obstruction. Pressure and return line hoses reversed at...

12 ► SPL31 User Manual Pulling Force...........................................................................................................................................16,647 lbs / 7550 kg- Pressure .................................................................................................

SPL31 User Manual ◄ 13 1 2 3 4 5 6 7 9 10 11 12 13 14 15 16 17 ITEM PART NO. QTY DESCRIPTION 1 1 O-RING* (PART OF SEAL KIT) 2 1 O-RING* (PART OF SEAL KIT) 3 03009 ROLL PIN (SPL31A-S, SPL31A-N ONLY) 4 21089 1 ROLL PIN 5 1 ROD WIPER * (PART OF SEAL KIT) 6 22914 1 SPOOL SEAL CAP 7 22919 1 HEADED TRIGGE...

14 ► SPL31 User Manual 2 3 4 5 7 8 9 10 11 18 19 20 22 23 24 27 28 29 30 31 32 33 34 36 37 38 39 40 43 44 45 46 24 46 4 10 55 49 50 FOR PARTS TO HANDLE ASSEMBLY SEE PAGE 13 SEE PAGE 6 FOR DECAL P/N’s PISTON PISTON ROD SPL31A SPL31A-N SPL31A-S PARTS ILLUSTRATION

SPL31 User Manual ◄ 15 * DENOTES PART IN SEAL KIT SEAL KIT 73042 ITEM P/N. QTY. DESCRIPTION 2 00596 4 CAPSCREW 3 1 O-RING* (PART OF SEAL KIT) 4 00664 2 RETAINING RING 5 1 O-RING* (PART OF SEAL KIT) 7 03972 1 COUPLER,FEMALE 3/8NPT FL.FACE SET P/N-03971 (SP- L31A AND SPL31A-S ONLY) 47436 1 COUPLER,FEM...