Stanley RV06 - Manual - manualsarea.com

Page 3 - WARNING; SERIOUS INJURY OR DEATH COULD RESULT FROM THE IMPROPER REPAIR OR; TABLE OF CONTENTS; IMPORTANT

RV06 User Manual ◄ 3 SERVICING: This manual contains safety, operation, and routine maintenance instructions. Stanley Hydraulic Tools recommends that servicing of hydraulic tools, other than routine maintenance, must be performed by an au- thorized and certified dealer. Please read the following war...

Page 4 - LOCAL SAFETY REGULATIONS; DANGER; CAUTION; CAUTION; NOTICE; SAFETY SYMBOLS

4 ► RV06 User Manual Always observe safety symbols. They are included for your safety and for the protection of the tool. LOCAL SAFETY REGULATIONS Enter any local safety regulations here. Keep these instructions in an area accessible to the operator and mainte- nance personnel. Safety symbols and si...

Page 5 - SAFETY PRECAUTIONS

RV06 User Manual ◄ 5 Tool operators and maintenance personnel must always comply with the safety precautions given in this manual, and on the stickers and tags attached to or on the tool and hose(s).These safety precautions are for your safety. Review them carefully before operating the tool or perf...

Page 7 - HOSE SAFETY TAGS; HOSE TYPES

RV06 User Manual ◄ 7 The rated working pressure of the hydraulic hose must be equal to or higher than the relief valve setting on the hy- draulic system. There are three types of hydraulic hose that meet this requirement and are authorized for use with Stanley Hydraulic Tools. They are: Certified no...

Page 8 - Tool to Hydraulic Circuit Hose Recommendations; HOSE RECOMMENDATIONS

8 ► RV06 User Manual Oil Flow Hose Lengths Inside Diameter USE ( Press/Return) Min. W orking Pressure GPM LPM FEET METERS INCH MM PSI BAR Certified Non-Conductive Hose - Fiber Braid - for Utility Bucket T rucks 4-9 15-34 up to 10 up to 3 3/8 10 Both 2250 155 Conductive Hose - W ire Braid or Fiber Br...

Page 9 - HTMA / EHTMA REQUIREMENTS

RV06 User Manual ◄ 9 Flow Range Nominal Operating Pressure (at the power supply outlet) System relief valve setting (at the power supply outlet) Maximum back pressure (at tool end of the return hose) Measured at a max. fluid viscosity of: (at min. operating temperature) Temperature: Sufficient heat ...

Page 10 - PREOPERATION PROCEDURES; CONNECT HOSES; CONNECTING A TOOL TO THE RV06; CONNECTING A DOUBLE-ACTING TOOL; OPERATION

10 ► RV06 User Manual PREOPERATION PROCEDURES CONNECT HOSES 1. If the RV06 is to be used on or near electrical lines, both of the hoses used to connect the RV06 to the intensifier must be labeled and certified non-con - ductive (see Hose Recommendations). Both pres- sure and return hoses must be rat...

Page 11 - OPERATING PROCEDURES; COLD WEATHER OPERATION

RV06 User Manual ◄ 11 OPERATING PROCEDURES • Observe all safety precautions given in this manual. • Refer to the applicable manual for the tool connect- ed to the RV06. • Activate the parent circuit to provide power to the in- tensifier. Pressure will now be available at the pres - sure port of the ...

Page 12 - TOOL PROTECTION & CARE

12 ► RV06 User Manual NOTICE In addition to the Safety Precautions found in this manual, observe the following for equipment protection and care. • Make sure all critical tool markings, such as labels and warning decals, are securely in place and leg- ible. Replace any that are damaged or missing. •...

Page 13 - TROUBLESHOOTING

RV06 User Manual ◄ 13 If symptoms of poor performance develop, the following chart can be used as a guide to correct the problem.When diagnosing faults in operation of the control valve, always check that the high-pressure hydraulic power source is supplying the correct hydraulic flow and pressure t...

Page 14 - HYDRAULIC SYSTEM REQUIREMENTS; SPECIFICATIONS

14 ► RV06 User Manual Weight ................................................................................................................................................... 2.6 lb/1.18 kg Length.........................................................................................................

Page 15 - RV06 PARTS ILLUSTRATION

Page 16 - RV06 PARTS LIST

16 ► RV06 User Manual ITEM PART NO. QTY DESCRIPTION 1 05338 1 BODY 2 12838 1 PIPE COUPLING 1/4 NPT 3 23128 2 HOSE ASSY 4 05337 1 NIPPLE 5 15399 1 BACK-UP RING 6 00018 1 O-RING 7/16 × 9/16 × 1/16 • 7 12227 1 MANIFOLD CAP 8 08019 1 BEARING RACE 9 08020 1 NEEDLE BEARING 10 18092 1 TRANSFER DISC 11 1225...

Stanley RV06 - Manual

Table of Contents:

Summary

Other Stanley Models