Page 2 - All; DECLARATION OF CONFORMITY
2 ► CS25/28 User Manual DECLARATION OF CONFORMITY ÜBEREINSTIMMUNGS-ERKLARUNG DECLARATION DE CONFORMITE CEE DECLARACION DE CONFORMIDAD DICHIARAZIONE DI CONFORMITA Hydraulic Tools ______________________________________________________________________ I, the undersigned: Ich, der Unterzeichnende: Je so...
Page 3 - WARNING; TABLE OF CONTENTS; IMPORTANT
CS25/28 User Manual ◄ 3 SERVICING: This manual contains safety, operation, and routine maintenance instructions. Stanley Hydraulic Tools recommends that servicing of hydraulic tools, other than routine maintenance, must be performed by an au- thorized and certified dealer. Please read the following ...
Page 4 - LOCAL SAFETY REGULATIONS; DANGER; CAUTION; CAUTION; NOTICE; SAFETY SYMBOLS
4 ► CS25/28 User Manual Always observe safety symbols. They are included for your safety and for the protection of the tool. LOCAL SAFETY REGULATIONS Enter any local safety regulations here. Keep these instructions in an area accessible to the operator and mainte- nance personnel. Safety symbols and...
Page 5 - SAFETY PRECAUTIONS
CS25/28 User Manual ◄ 5 Tool operators and maintenance personnel must always comply with the safety precautions given in this manual and on the stickers and tags attached to the tool and hose.These safety precautions are given for your safety. Re- view them carefully before operating the tool and be...
Page 6 - POLE CHAIN SAW SPECIFIC
6 ► CS25/28 User Manual POLE CHAIN SAW SPECIFIC SAFETY PRECAUTIONS • Do not rely exclusively upon the safety devices built into the saw. As a pole saw user, several steps must be taken to keep your cutting jobs free from accident or injury. • With basic understanding of kickback, you can re- duce or...
Page 7 - WORKING IN PROXIMITY TO ELECTRICAL; ELECTRICAL HAZARDS
CS25/28 User Manual ◄ 7 The following guidelines must be followed to prevent accidental contact with overhead electrical conductors and/or communication wires and cables. (Ref. ANSI Z133.1-2000) WORKING IN PROXIMITY TO ELECTRICAL HAZARDS An inspection shall be made by a qualified arborist to determi...
Page 8 - STORM WORK AND EMERGENCY
8 ► CS25/28 User Manual Table 2 – Minimum approach distances to energized conductors for persons other than qualified line- clearance arborists and qualified line-clearance ar - borist trainees. Nominal Voltage kV phase-to-phase1) Distance ft-in m 0.0 – 1.0 10–00 3.05 1.1 – 15.0 10–00 3.05 15.1 – 36...
Page 10 - HOSE SAFETY TAGS; HOSE TYPES
10 ► CS25/28 User Manual The rated working pressure of the hydraulic hose must be equal to or higher than the relief valve setting on the hy- draulic system. There are three types of hydraulic hose that meet this requirement and are authorized for use with Stanley Hydraulic Tools. They are: Certifie...
Page 11 - Tool to Hydraulic Circuit Hose Recommendations; HOSE RECOMMENDATIONS
CS25/28 User Manual ◄ 11 Oil Flow Hose Lengths Inside Diameter USE ( Press/Return) Min. W orking Pressure GPM LPM FEET METERS INCH MM PSI BAR Certified Non-Conductive Hose - Fiber Braid - for Utility Bucket T rucks 4-9 15-34 up to 10 up to 3 3/8 10 Both 2250 155 Conductive Hose - W ire Braid or Fibe...
Page 12 - HTMA / EHTMA REQUIREMENTS
12 ► CS25/28 User Manual Flow Range Nominal Operating Pressure (at the power supply outlet) System relief valve setting (at the power supply outlet) Maximum back pressure (at tool end of the return hose) Measured at a max. fluid viscosity of: (at min. operating temperature) Temperature: Sufficient h...
Page 13 - PRE-OPERATION PROCEDURES
CS25/28 User Manual ◄ 13 screw located in the top of the valve spool fully in (clock- wise) until it bottoms. TO DISABLE DUAL SPOOL OPERATION AND CONVERT TO OC ONLY OPERATION Turn the selector screw located in the top of the valve spool fully out (counter-clockwise) until it hits the stop.1. Insert ...
Page 14 - FELLING OR BACK CUT; LOGS/LIMBS WITH PRESSURE ON; TOOL OPERATION; CUTTING TIPS; FELLING OR TOPPING; NOTCHING OR UNDERCUTTING; OPERATION
14 ► CS25/28 User Manual 4. WARNING Watch for falling limbs. Make a diagonal cut down to meet the horizontal cut and remove the wood from the notch. FELLING OR BACK CUT 5. The felling or back cut is made on the side opposite and at least 2 inches above the horizontal undercut (the felling cut is mad...
Page 15 - COLD WEATHER OPERATION
CS25/28 User Manual ◄ 15 PRUNING & TRIMMING 1. Observe all safety precautions.2. Use both hands. Keep a firm grip.3. Be alert for kickback. Do not allow the tip of the bar to touch anything while the chain is in motion. Figure 3. Crosscutting Logs/Limbs with Pressure on Bottom 4. Pole chain saws...
Page 16 - CHAIN TENSION ADJUSTMENT; AUTOMATIC OILER ADJUSTMENT
16 ► CS25/28 User Manual CHAIN TENSION ADJUSTMENT 1. Observe all safety precautions.2. When the chain appears loose, lubricate it well and let it cool for a few minutes to allow for contraction of the chain. Disconnect the pole chain saw from its hydraulic power source. NOTE: Perform Steps 3 through...
Page 17 - TOOL PROTECTION & CARE
CS25/28 User Manual ◄ 17 • Make sure all couplers are wiped clean before con- nection. • The hydraulic circuit control valve must be in the OFF position when coupling or uncoupling hydraulic tools. Failure to do so may result in damage to the quick couples and cause overheating of the hydrau- lic sy...
Page 18 - TROUBLESHOOTING
18 ► CS25/28 User Manual If symptoms of poor performance develop, the following chart can be used as a guide to correct the problem.When diagnosing faults in operation of the pole chain saw, always make sure the hydraulic power source is supply- ing the correct hydraulic flow and pressure as listed ...
Page 19 - ACCESSORIES; SERVICE TOOLS
CS25/28 User Manual ◄ 19 Capacity CS25 and CS28 .................................................................................... 12 and 15 inch/30 and 38 cm Cut Lengths Weight (w/o Bar and Chain) .......................................................................................................
Page 20 - CS25 / CS28 PARTS ILLUSTRATION
20 ► CS25/28 User Manual To order complete motor assembly see “Note” on parts list (Page 21). CS25 / CS28 PARTS ILLUSTRATION
