Smeg SIM1643DS - User Manual

Instructions 39 EN • Use cables withstanding a temperature of at least 90°C. • The tightening torque of the screws of the terminal supply wires must be 1.5 - 2 Nm. • The power cable must only be installed or replaced by a qualified technician. For this appliance • If cracks or fissures form, or if t...

Instructions 40 • Let the cooking surface cool down before closing the cover. • People who have pacemakers or other similar devices fitted must make sure that the operation of these devices is not affected by the induction field, the frequency range of which is between 20 and 50 kHz. • In conformity...

Instructions 41 EN 1.6 Disposal This appliance conforms to the WEEE European directive (2012/19/EU) and must be disposed of separately from other waste at the end of its service life. The appliance does not contain substances in quantities sufficient to be considered hazardous to health and the envi...

Instructions 42 1.7 How to read the user manual This user manual uses the following reading conventions: 1. Sequence of instructions for use.• Standalone instruction. Instructions General information on this user manual, on safety and final disposal. Description Description of the appliance and its ...

Description 43 EN 2 Description 2.1 General Description 60 cm SX = Left cooking zones CNT = Centre cooking zones DX = Right cooking zones Maximum absorbed power table (Watt) * power levels are approximate and may vary according to the pan used or the settings made. Dimensions H x L (mm) Level 9 Boos...

Description 44 2.2 Control panel Cooking zones area List of buttons Scroll bar: increases or decreases the power level of a cooking zone. Warming function button: activates the keep warm function. List of icons Scroll bar and number icon: indicate the power level that has been selected for a cooking...

Description 45 EN Advantages of induction cooking • Energy saving thanks to the direct transmission of energy to the pan (suitable magnetisable cookware is required) compared to traditional electric cooking. • Improved safety as the energy is only transmitted to the pan placed on the hob. • High lev...

Use 46 3 Use 3.1 Instructions High temperature Danger of burns • Protect your hands by wearing heat- proof gloves during use. • Do not touch or clean the hob surface during operation or when the residual heat indicator lights are still on. • Do not put empty pans or frying pans on switched on cookin...

Use 47 EN 3.2 Preliminary operations In order to remove any moisture that could have accumulated during the manufacturing process and for the electronic circuits and control keypad to work properly:1. Remove the protective films from the external surfaces of the appliance and accessories. 2. Remove ...

Use 48 To see whether the pan is suitable, bring a magnet close to the bottom: if it is attracted, the pan is suitable for induction cooking.If you do not have a magnet, you can put a small amount of water in the pan, place it on a cooking zone and start the hot plate. If the symbol appears on the d...

Use 49 EN Advice on energy-saving • The diameter of the base of the pan must not exceed the width of the silk-screened cooking zone. • Pans must not be placed outside the perimeter of the hob or above the front control panel. • When buying a pan, check whether the diameter indicated is that of the b...

Use 50 Switching on the cooking zone automatically After switching on the hob:1. Position a pan (suitable for induction cooking and not empty) on the cooking zone you wish to use. 2. The display corresponding to the zone on which the container has been placed turns on automatically and displays . Ad...

Use 51 EN Quick selection After having switched on the hob and placed a pan on it:1. Place a finger on the scroll bar at approximately the required power level. 2. The cooking zone automatically switches on at the selected power level. Booster Function After switching on the hob and having selected ...

Use 52 Double Booster Function The Double Booster function allows more power to be supplied compared to the Booster function.After having activated the Booster function for a cooking zone, press the far right of the scroll bar again. The symbols , and will be displayed in sequence. Multizone functio...

Use 53 EN If a large, oval or oblong pan is being used, make sure that it is placed in the centre of the cooking zone. Example of correct pan position Example of incorrect pan position Examples of griddle position To deactivate the Multizone function: 1. Touch the scroll bar of the relevant zones at...

Use 54 Residual heat If the cooking zone is still hot after being switched off, the symbol will be displayed on the display. The symbol clears once the temperature drops below 65°C. 3.4 Special functions Warming Function To activate the Warming function, first turn on the hob, then:1. Place a pan on...

Use 55 EN Grill Function To activate the Grill function: 1. Place a griddle or a long pan on the right zones. 2. Press the button. The LED above it will flash. The symbol appears on the front zone display and the symbol appears on the rear zone display. The scroll bar will be set automatically to le...

Use 56 • After the heating time has elapsed, the cooking zone reverts to the previously selected power level. This function can be deactivated by selecting and holding a different power level or by switching the appliance off. Timer After having switched on the hob, without having activated a cookin...

Use 57 EN Timed cooking To activate the timed cooking function, first turn on the hob, then:1. Place a pan on the cooking zone and select a power level. 2. Press the and buttons at the same time. The icon appears at the side of the number icon of the zone. 3. Use the and buttons to select the requir...

Use 58 The Recall function only allows the following functions to be restored:1 Functions and power levels of the cooking zones. 2 Timed cooking. 3 Multizone function. 4 Rapid heating. 5 Booster functions. 6 Controls lock. 3.6 Error notifications If the appliance malfunctions or operates incorrectly...

Cleaning and maintenance 59 EN 4 Cleaning and maintenance 4.1 Instructions 4.2 Cleaning the surfaces To keep the surfaces in good condition, they should be cleaned regularly after use. Let them cool first. 4.3 Ordinary weekly cleaning Clean and maintain the hob once a week using an ordinary glass cl...

Cleaning and maintenance 60 Changes in colour do not affect the operation and stability of the glass. These are not alterations to the material of the hob but just residues which have not been removed and have then carbonised. Shiny surfaces can form due to the bases of pans, especially aluminium on...

Installation 61 EN 5 Installation 5.1 Electrical connection General information Check the grid characteristics against the data indicated on the plate.The identification plate bearing the technical data, serial number and brand name is visibly positioned on the appliance.Do not remove this plate for...

Installation 62 Testing At the end of installation, carry out a brief inspection test. If the hob fails to operate, after checking that you have carried out the instructions correctly, unplug the appliance and contact Technical Support. 5.2 Instructions for the installer • Do not bend or trap the po...

Installation 63 EN 5.4 Safety instructions Veneers, adhesives or plastic coatings on adjacent furniture should be temperature-resistant ( >90°C ), otherwise they might warp over time.The minimum clearance between exhaust hoods and the cooking surface must be at least the distance indicated in the...

Installation 64 Hob seal To prevent leakage of liquid between the frame of the hob and the countertop, place the adhesive seal provided along the entire outer edge of the hob before assembly. Flush built-in model For this kind of hobs additional milling is needed in the recessed hole if you wish to ...

Installation 65 EN 5.6 Mounting Over built-in oven unit The clearance between the hob and the kitchen units or other built-in appliances must be enough to ensure sufficient ventilation and air discharge. If installed above an oven, a space must be left between the bottom of the hob and the top of th...

Installation 66 Ventilation The illustrations below show two examples of installation suitable for proper ventilation and one example of incorrect installation to be avoided. Spring clips To ensure the hob is fixed and centred as accurately as possible, the clips provided must be positioned as descr...