Smeg PXL664AU - User Manual

Description 7 EN 2 Description 2.1 General Description 60 cm 75 cm

Description 8 100 cm AUX = AuxiliarySR = Semi-rapidRR = Reduced rapid R = RapidUR = Ultra rapid 2.2 Symbols Cooking zones Front left Centre left Rear left Central Rear right Central right Front right Burner knobs Useful for lighting and adjusting the hob burners. Press and turn the knobs anti- clock...

Use 9 EN 3 Use 3.1 Instructions 3.2 First use 1. Remove any protective film from the outside or inside of the appliance, including accessories. 2. Remove any labels (apart from the technical data plate) from accessories. 3. Remove and wash all the appliance accessories (see 4 Cleaning and maintenanc...

Use 10 3.3 Using the hob All the appliance’s control and monitoring devices are located together on the front panel. The burner controlled by each knob is shown next to the knob. The appliance is equipped with an electronic ignition device. Simply press the knob and turn it anti-clockwise to the max...

Use 11 EN Correct positioning of the grids The grids over the burners must be positioned in parallel to the control panel, not perpendicular.Each type of burner must be associated with its own grid.Use the igniter and thermocouple indentations as a reference in order to correctly position the grid o...

Cleaning and maintenance 12 4 Cleaning and maintenance 4.1 Instructions 4.2 Cleaning the appliance To keep the surfaces in good condition, they should be cleaned regularly after use. Let them cool first. Ordinary daily cleaning Always use only specific products that do not contain abrasives or chlor...

Cleaning and maintenance 13 EN Igniters and thermocouples For correct operation the igniters and thermocouples must always be perfectly clean. Check them frequently and clean them with a damp cloth if necessary. Remove any dry residues with a wooden toothpick or a needle. Flame-spreader crowns and b...

Installation 14 5 Installation 5.1 Clearances above and around domestic appliances This appliance must be installed by an authorised person in accordance with this instruction manual, AS/NZS 5601.1 – Gas installations (installation and pipe sizing), local gas fitting regulations, local electrical re...

Installation 15 EN 3. Additional requirements for Freestanding and Elevated Cooking Appliaces – (Measurements D & E) Where D, the distance from the periphery of the nearest burner to a horizontal combustible surface is less than 200 mm, then E shall be 10 mm or more, or the horizontal surface sh...

Installation 16 5.3 Section cut from the countertop Create an opening with the dimensions shown in the figure in the countertop of the piece of furniture. 5.4 Mounting Over built-in oven unit The clearance between the hob and the kitchen furniture or other installed appliances must be enough to ensu...

Installation 17 EN Over empty kitchen unit or drawers If there are other pieces of furniture (lateral walls, drawers, etc.), dishwashers or fridges under the hob, a double-layer wooden base must be installed at least 20 mm from the bottom of the hob to avoid any accidental contact. It must only be p...

Installation 18 With steel hob To prevent leakage of liquid between the frame of the hob and the work surface, put the insulating seal provided in position before assembly.1. Refer to the dimensions in the figure, bearing in mind that the long front side must brush against the hole. 2. Use light pre...

Installation 19 EN Connection of the appliance to the gas supply must be in accordance with the requirements of AS5601. A ½” BSP connector at the inlet is recommended and the gas supply line to the appliance must be of adequate length to allow sufficient withdrawal of appliance for service or discon...

Installation 20 Room ventilation The room containing the appliance should have a permanent air supply in accordance with the standards in force. The room where the appliance is installed must have enough air flow needed for the regular combustion of gas and the necessary air change in the room itsel...

Installation 21 EN 5.6 Adaptation to different types of gas If other types of gas are to be used, the nozzles must be replaced and the primary air must be adjusted. In order to replace the nozzles and adjust the burners, the hob top must be removed. Removing the hob top 1. Remove the grids from the ...

Installation 22 5. Remove the screws that fasten the hob top to the burner casing (the figure shows the 60 cm model as an example). 6. Lift the hob top and remove it. Replacing nozzles 1. Unscrew screw A and push air regulator B as far as it will go. 2. Use a spanner to remove the nozzles C and inst...

Installation 23 EN Adjusting the minimum setting for natural or town gas 1. Light the burner and turn it to the minimum position. 2. Extract the gas cock knob and turn the adjustment screw next to the tap rod (depending on the model) until the correct minimum flame is achieved. 3. Refit the knob and...

Installation 24 5.7 Electrical connection General information Check the grid characteristics against the data indicated on the plate.The identification plate bearing the technical data, serial number and brand name is visibly positioned on the appliance.Do not remove this plate for any reason.Perfor...