Page 2 - en
Building Technologies i TEL50.GSM en English 1. I NTRODUCTION ......................................................... 1 1.1 Copyright .............................................................. 1 1.2 Trademarks .......................................................... 1 1.3 Declaration of conf...
Page 3 - Introduction
Building Technologies - 1 - TEL50.GSM en English 1. Introduction Thank you for choosing this product. Please read this manual carefully to optimize use of the TEL50.GSM. 1.1 Copyright Siemens S.p.A. All rights reserved. The reproduction, modification or transcription of this document without prior w...
Page 4 - Declaration of conformity
Building Technologies - 2 - TEL50.GSM 1.3 Declaration of conformity Siemens S.p.A. Building Technologies Viale Piero ed Alberto Pirelli, 10 - 20126 Milano (MI) Italy declares on its sole responsibility that the following product: TEL50.GSM complies with the regulations in force with reference to the...
Page 5 - Contents of sales pack
Building Technologies - 3 - TEL50.GSM 1.4 Warranty This product is guaranteed against any material and manufacture defects. SIEMENS reserves the right, at its own discretion, to repair or replace faulty products. The warranty is deemed null and void if the fault is caused by improper use or by an op...
Page 6 - Instructions; Safety instructions
Building Technologies - 4 - TEL50.GSM 2. Instructions In order to use the product safely and efficiently, please read the following instructions carefully before use. The product may only be employed for the use for which it has been conceived and manufactured. Any other use shall be considered the ...
Page 8 - Operating instructions; adequate GSM coverage
Building Technologies - 6 - TEL50.GSM 2.2 Operating instructions 1. The SIM Card must always be inserted and removed when there is no power supply. If not, the SIM Card read interface inside the GSM module could be damaged. 2. Always disable the PIN code of the SIM card. If not, the TEL50.GSM cannot...
Page 9 - General information; Cycle
Building Technologies - 7 - TEL50.GSM 3. General information The TEL50.GSM phone remote control has been designed for remote operation of electrical or electro-hydraulic equipment such as room thermostats, boilers, burners, heaters, zone valves, circulation pumps, irrigation systems, etc. It is part...
Page 10 - Installation; Electrical connections
Building Technologies - 8 - TEL50.GSM 4. Installation Comply with the permitted temperature and humidity conditions (see Technical Data). 4.1 Wall-mounting Mount the device on the wall or 3-module flush-mounted box (503 type) using the special holes in the rear part of the container. During installa...
Page 11 - TEMP; Connecting terminals.
Building Technologies - 9 - TEL50.GSM OUT1 - Relay output 1 Potential-free relay contact for control of special devices (boiler, zone valve, heater, etc.). Observe the max current rating of the electrical contacts indicated in the technical data. TEMP - Analog input for connection of an LG-Ni1000 te...
Page 13 - Connection of stilo antenna; PARAMETER
Building Technologies - 11 - TEL50.GSM 4.3 Connection of stilo antenna The TEL50.GSM is supplied with its own dual band stilo antenna with the following characteristics: PARAMETER CHARACTERISTICS Profile Dual-Band GSM 900MHz band 890-960MHz 1,800MHz band 1710-1,880MHz Impedance 50 ohm WSVR <= 1:1...
Page 14 - Recommendations for use of fixed or external antenna; Insertion of SIM card
Building Technologies - 12 - TEL50.GSM Recommendations for use of fixed or external antenna You are advised to observe the following recommendations: • The antenna must be placed at least 2m from any electronic equipment, at least 15cm from any obstacles and in a position where there is good recepti...
Page 15 - Checking of indicator lamps; LEDs
Building Technologies - 13 - TEL50.GSM 4.6 Checking of indicator lamps The TEL50.GSM has 5 LED indicator lamps. Three of these can be seen on the front of the device and the other two are located in the lower part and can be seen through the plastic grid. LEDs On Off OUT1 (red) contact closed contac...
Page 16 - Technical data
Building Technologies - 14 - TEL50.GSM 5. Technical data Power supply 10…30 VDC stabilized (230VAC +10 -15% 50-60Hz with supplied power supply) Average consumption In operation: 700mA @ 12VDC On stand-by: 60mA @ 12VDC LED indicator lamps - Power supply present - GSM field present - Status of alarm i...
Page 17 - Basic configuration; Commands via DTMF tones; Device ID
Building Technologies - 15 - TEL50.GSM 6. Basic configuration With the factory configuration, the TEL50.GSM can already handle the following voice (DTMF tones) and SMS commands. In order to operate safely and correctly, the device must be correctly connected to the GSM network (see par. 4.6). Carefu...
Page 18 - Commands via SMS
Building Technologies - 16 - TEL50.GSM When the “#” tone is received, if the command is effected, the sequence of corresponding beeps (ON or OFF) is generated. If the command is not recognized or is not applicable (for example, if an ON command is sent to an input “31#”), the ERROR tone is generated...
Page 19 - Temperature sensor querying
Building Technologies - 17 - TEL50.GSM SMS text SMS reply Action OUT1=1 OUT1=1 closes contact relay 1 OUT1=0 OUT1=0 opens contact relay 1 OUT2=1 OUT2=1 closes contact relay 2 OUT2=0 OUT2=0 opens contact relay 2 OUT1 OUT1=0 or OUT1=1 (*) queries the status of contact relay 1 – OUT1=0 contact open OUT...
Page 20 - Extended configuration; Creation of a qualified user list
Building Technologies - 18 - TEL50.GSM 7. Extended configuration Using the basic configuration already present, the user can customize device parametrization by changing some of the system parameters via SMS. Carefully note any changes made and keep them with these instructions in order to ensure th...
Page 22 - Modification of Input-Output identification string
Building Technologies - 20 - TEL50.GSM 7.2 Modification of Input-Output identification string In this section the User can modify the identification string (ALIAS) for the device inputs/outputs. If no changes are made, the factory settings are maintained. The defined alias will have a maximum length...
Page 27 - Environmental compatibility and disposal; Comply with all local laws that are in force.
Building Technologies - 25 - TEL50.GSM 8. Environmental compatibility and disposal This product has been developed and constructed using materials and processes that take account of environmental issues. Refer to the following notes for disposal of the product at the end of its service life or if it...
Page 29 - Siemens SpA
Building Technologies - 27 - TEL50.GSM Siemens SpA Building Technologies Viale Piero ed Alberto Pirelli, 10 I - 20126 Milano - I Tel 02 243 1 Fax 02 243 65 750 www.siemens.it/sbt
