Page 2 - Warnings, Cautions and Notes; Specific Warnings, Cautions and Notes; that apply to particular activities are; WARNING
Warnings, Cautions and Notes Issue 11/04 SINAMICS G110 2 Operating Instructions (Compact) The Compact version of the Operating Instructions will cover the majority of typical applications. It is valid for inverters firmware versions 1.0 and 1.1. For full details please refer to the Operating Instruc...
Page 3 - NOTES; t monitoring
Issue 11/04 Warnings, Cautions and Notes SINAMICS G110 Operating Instructions (Compact) Operating Instructions (Compact) 3 NOTES ¾ This equipment is capable of providing internal motor overload protection in accordance with UL508C section 42 (refer to P0610 and P0335). I 2 t monitoring is ON by defa...
Page 5 - Contents; Establishing communications SINAMICS G110
Issue 11/04 Contents SINAMICS G110 Operating Instructions (Compact) 5 Contents 1 Installation ............................................................................................................... 6 1.1 Clearance distances for mounting ..........................................................
Page 6 - Installation; Clearance distances for mounting; Clearance distances for mounting; dimensions; Drilling Dimensions; Bolts Nm
1 Installation Issue 11/04 SINAMICS G110 6 Operating Instructions (Compact) 1 Installation 1.1 Clearance distances for mounting The inverters can be mounted adjacent to each other. If they are mounted on top of each other, however, a clearance of 100 mm has to be observed. 15 mm 100 mm 15 mm FSA FSB...
Page 7 - Electrical Installation; Electrical; specifications; Term. Designation Function
Issue 11/04 2 Electrical Installation SINAMICS G110 Operating Instructions (Compact) 7 2 Electrical Installation 2.1 Technical specifications 1 AC 200 - 240 V r 10 %, 47 - 63 Hz 0AB 11-2xy0* 12-5xy0* 13xy0* 15xy0* 17xy0* 21-1xy0* 21-5xy0* 22-2xy0* 23-0xy0* Order No. 6SL3211- 0KB 11-2xy0* 12-5xy0* 13...
Page 8 - diagram; Inverter block diagram
2 Electrical Installation Issue 11/04 SINAMICS G110 8 Operating Instructions (Compact) 2.4 Block diagram Fig. 2-2 Inverter block diagram
Page 9 - Factory setting; Factory; Further factory setting; Specific factory settings for the analog version; Digital input
Issue 11/04 3 Factory setting SINAMICS G110 Operating Instructions (Compact) 9 3 Factory setting The SINAMICS G110 frequency inverter has already been programmed at the factory (motor parameters P0304, P0305, P0307, P0310), for standard V/f applications on Siemens 4-pole asynchronous motors 1LA that...
Page 10 - Specific factory settings for the USS version; Inputs Terminals; switches; Bus termination on USS variant; A common 0 V reference
3 Factory setting Issue 11/04 SINAMICS G110 10 Operating Instructions (Compact) 3.2 Specific factory settings for the USS version Inputs Terminals Parameter Function Command source P0700 = 5 Via the USS protocol Setpoint source P1000 = 5 Frequency input via the USS protocol USS address P2011 = 0 USS...
Page 11 - Communications; STARTER
Issue 11/04 4 Communications SINAMICS G110 Operating Instructions (Compact) 11 4 Communications 4.1 Establishing communications SINAMICS G110 STARTER The following optional components are additionally required in order to establish communications between STARTER and SINAMICS G110: ¾ PC <-> f...
Page 12 - Buttons and their Functions; Function Effects
5 BOP (Option) Issue 11/04 SINAMICS G110 12 Operating Instructions (Compact) 5 BOP (Option) 5.1 Buttons and their Functions Panel/Button Function Effects Indicates Status The LCD displays the settings currently used by the converter. Start converter Pressing the button starts the converter. This but...
Page 14 - Cloning parameters with the BOP; Upload (SINAMICS G110
5 BOP (Option) Issue 11/04 SINAMICS G110 14 Operating Instructions (Compact) 5.3 Cloning parameters with the BOP A single parameter set can be uploaded from an inverter SINAMICS G110 and then downloaded into another SINAMICS G110 inverter. To clone a parameter set from one inverter to another, the f...
Page 15 - Commissioning; commissioning; START; Quick commissioning
Issue 11/04 6 Commissioning SINAMICS G110 Operating Instructions (Compact) 15 6 Commissioning 6.1 Quick commissioning The quick commissioning function will adapt the inverter to the motor and will set important technological parameters. The quick commissioning can be omitted if a 4-pole 1LA Siemens ...
Page 16 - For slip compensation, the input is absolutely necessary.
6 Commissioning Issue 11/04 SINAMICS G110 16 Operating Instructions (Compact) P0308 =... P0308 =... Rated motor cosPhi (Nominal motor power factor (cos M ) from rating plate) If the setting is 0, the value is automatically calculated P0100 = 1: P0308 no significance, no entry required. P0309 =... P0...
Page 17 - END; Commissioning the application
Issue 11/04 6 Commissioning SINAMICS G110 Operating Instructions (Compact) 17 P1300 =... Control mode (enters the required control mode) 0 V/f with linear characteristic 2 V/f with quadratic characteristic 3 V/f with programmable characteristic P3900 = 1 End of quick commissioning (means: the start ...
Page 18 - Selection of command source; inputs
6 Commissioning Issue 11/04 SINAMICS G110 18 Operating Instructions (Compact) 6.2.2 Selection of command source P0700 G110 AIN G110 USS Settings 0 X X – 1 X X – 2 X X See 6.2.3 P0700 =... Selection of command source Selects digital command source. 0 Factory fault setting 1 BOP (keypad) 2 Terminal 5 ...
Page 19 - Function of digital output 0*; Selection of frequency setpoint
Issue 11/04 6 Commissioning SINAMICS G110 Operating Instructions (Compact) 19 6.2.4 Digital output (DOUT) P0731 =... Function of digital output 0* Defines source of digital output 0. P0748 = 0 Invert digital output Allows the signals to be output to be inverted. Status of DOUT at logically active si...
Page 20 - MOP setpoint will not be stored
6 Commissioning Issue 11/04 SINAMICS G110 20 Operating Instructions (Compact) 6.2.6 Analog input (ADC) P0757 =... Value x1 of ADC scaling P0758 =... Value y1 of ADC scaling This parameter represents the value of x1 as a % of P2000 (reference frequency). P0759 =... Value x2 of ADC scaling P0760 =... ...
Page 21 - Fixed frequency 1
Issue 11/04 6 Commissioning SINAMICS G110 Operating Instructions (Compact) 21 6.2.8 Fixed frequency (FF) There are 2 types of fixed frequencies: 1. Direct selection (P0701 – P0703 =15) 2. Direct selection + ON command (P0701 – P0703 = 16) For P0727 = 2, 3: if more than one setting ‘16’ is used, each...
Page 22 - limit; V/f with quadratic characteristic
6 Commissioning Issue 11/04 SINAMICS G110 22 Operating Instructions (Compact) 6.2.10 Ramp-function generator (HLG) P1091 =... Skip frequency (entered in Hz) Defines skip frequency which avoids effects of mechanical resonance and suppresses frequencies within +/- 2 Hz (skip frequency bandwidth). 2 Hz...
Page 23 - Continuous boost; Validity range; Boost voltage; Acceleration boost; Starting boost
Issue 11/04 6 Commissioning SINAMICS G110 Operating Instructions (Compact) 23 Continuous boost (entered in %) Voltage boost as a % relative to P0305 (rated motor current) and P0350 (stator resistance). P1310 is valid for all V/f characteristics (refer to P1300). At low output frequencies, the effect...
Page 24 - protection; functions; start
6 Commissioning Issue 11/04 SINAMICS G110 24 Operating Instructions (Compact) 6.2.13 Inverter/motor protection P0290 =... Inverter overload reaction Selects reaction of inverter to an internal overtemperature 0 Reduce output frequency 1 Trip (F0004 / F0005) P0335 =... Motor cooling (enters the motor...
Page 25 - restart; DC braking start frequency
Issue 11/04 6 Commissioning SINAMICS G110 Operating Instructions (Compact) 25 6.2.14.2 Automatic restart P1210 =... Automatic restart Configures automatic restart function. 0 Disabled 1 Trip reset after power on 2 Restart after mains blackout 3 Restart after mains brownout or fault 4 Restart after m...
Page 26 - controller; Configuration of Vdc controller
6 Commissioning Issue 11/04 SINAMICS G110 26 Operating Instructions (Compact) 6.2.14.5 Vdc controller P1240 =... Configuration of Vdc controller Enables / disables Vdc controller. 0 Vdc controller disabled 1 Vdc-max controller enabled NOTE P1240 = 1 prevents an overvoltage condition of the DC link (...
Page 27 - When replacing SINAMICS G110 frequency inverters.; Parameter reset to factory setting; Displays and messages; LED status display; Fault messages and Alarm messages
Issue 11/04 7 Displays and messages SINAMICS G110 Operating Instructions (Compact) 27 6.3 Series commissioning An existing parameter set can be transferred to a SINAMICS G110 frequency inverter using STARTER or BOP (see 5.3). Typical applications for series commissioning include: 1. If several drive...
Page 28 - Standard; Drives; Postfach; Subject to change without prior notice; Information about SINAMICS G110 is also available from:; Regional Contacts; America; Online Service & Support; Customers can access technical and general information at:
SINAMICS G110 Operating Instructions (Compact) Siemens AG Automation & Drives Standard Drives Postfach 3269, D – 91050 Erlangen Germany www.siemens.com © Siemens AG 2004 Subject to change without prior notice Issue 11/04 Information about SINAMICS G110 is also available from: Regional Contacts P...
