Siemens TEL50.GSM - Manuals

Building Technologies - 3 - TEL50.GSM 1.4 Warranty This product is guaranteed against any material and manufacture defects. SIEMENS reserves the right, at its own discretion, to repair or replace faulty products. The warranty is deemed null and void if the fault is caused by improper use or by an op...

Building Technologies - 4 - TEL50.GSM 2. Instructions In order to use the product safely and efficiently, please read the following instructions carefully before use. The product may only be employed for the use for which it has been conceived and manufactured. Any other use shall be considered the ...

Building Technologies - 6 - TEL50.GSM 2.2 Operating instructions 1. The SIM Card must always be inserted and removed when there is no power supply. If not, the SIM Card read interface inside the GSM module could be damaged. 2. Always disable the PIN code of the SIM card. If not, the TEL50.GSM cannot...

Building Technologies - 7 - TEL50.GSM 3. General information The TEL50.GSM phone remote control has been designed for remote operation of electrical or electro-hydraulic equipment such as room thermostats, boilers, burners, heaters, zone valves, circulation pumps, irrigation systems, etc. It is part...

Building Technologies - 8 - TEL50.GSM 4. Installation Comply with the permitted temperature and humidity conditions (see Technical Data). 4.1 Wall-mounting Mount the device on the wall or 3-module flush-mounted box (503 type) using the special holes in the rear part of the container. During installa...

Building Technologies - 9 - TEL50.GSM OUT1 - Relay output 1 Potential-free relay contact for control of special devices (boiler, zone valve, heater, etc.). Observe the max current rating of the electrical contacts indicated in the technical data. TEMP - Analog input for connection of an LG-Ni1000 te...

Building Technologies - 11 - TEL50.GSM 4.3 Connection of stilo antenna The TEL50.GSM is supplied with its own dual band stilo antenna with the following characteristics: PARAMETER CHARACTERISTICS Profile Dual-Band GSM 900MHz band 890-960MHz 1,800MHz band 1710-1,880MHz Impedance 50 ohm WSVR <= 1:1...

Building Technologies - 12 - TEL50.GSM Recommendations for use of fixed or external antenna You are advised to observe the following recommendations: • The antenna must be placed at least 2m from any electronic equipment, at least 15cm from any obstacles and in a position where there is good recepti...

Building Technologies - 13 - TEL50.GSM 4.6 Checking of indicator lamps The TEL50.GSM has 5 LED indicator lamps. Three of these can be seen on the front of the device and the other two are located in the lower part and can be seen through the plastic grid. LEDs On Off OUT1 (red) contact closed contac...

Building Technologies - 14 - TEL50.GSM 5. Technical data Power supply 10…30 VDC stabilized (230VAC +10 -15% 50-60Hz with supplied power supply) Average consumption In operation: 700mA @ 12VDC On stand-by: 60mA @ 12VDC LED indicator lamps - Power supply present - GSM field present - Status of alarm i...

Building Technologies - 15 - TEL50.GSM 6. Basic configuration With the factory configuration, the TEL50.GSM can already handle the following voice (DTMF tones) and SMS commands. In order to operate safely and correctly, the device must be correctly connected to the GSM network (see par. 4.6). Carefu...

Building Technologies - 16 - TEL50.GSM When the “#” tone is received, if the command is effected, the sequence of corresponding beeps (ON or OFF) is generated. If the command is not recognized or is not applicable (for example, if an ON command is sent to an input “31#”), the ERROR tone is generated...

Building Technologies - 17 - TEL50.GSM SMS text SMS reply Action OUT1=1 OUT1=1 closes contact relay 1 OUT1=0 OUT1=0 opens contact relay 1 OUT2=1 OUT2=1 closes contact relay 2 OUT2=0 OUT2=0 opens contact relay 2 OUT1 OUT1=0 or OUT1=1 (*) queries the status of contact relay 1 – OUT1=0 contact open OUT...

Building Technologies - 18 - TEL50.GSM 7. Extended configuration Using the basic configuration already present, the user can customize device parametrization by changing some of the system parameters via SMS. Carefully note any changes made and keep them with these instructions in order to ensure th...

Building Technologies - 20 - TEL50.GSM 7.2 Modification of Input-Output identification string In this section the User can modify the identification string (ALIAS) for the device inputs/outputs. If no changes are made, the factory settings are maintained. The defined alias will have a maximum length...

Building Technologies - 25 - TEL50.GSM 8. Environmental compatibility and disposal This product has been developed and constructed using materials and processes that take account of environmental issues. Refer to the following notes for disposal of the product at the end of its service life or if it...

Building Technologies - 27 - TEL50.GSM Siemens SpA Building Technologies Viale Piero ed Alberto Pirelli, 10 I - 20126 Milano - I Tel 02 243 1 Fax 02 243 65 750 www.siemens.it/sbt