Siemens SC9000 - User Manual
Siemens SC9000 – User Manual, read for free online in PDF format. We hope this helps you resolve any issues you may have. If you have further questions, please contact us through the contact form.
Table of Contents:
- Page 2 – the (4) nylon thumb screws on the back of the Mounting Plate.; Install 4” Cato Channel on Right Side; As described on Page 1 of this document.
- Page 3 – Tension Bolt to obtain the desired tension.; Swivel; located under the front end of the Arm.; Cable Management
- Page 4 – Cleaning; cloth. Dry the arm thoroughly after cleaning.; CAUTION; Siemens Power Supply Holster
DU-DR-0016-SC9000 Rev A 6/4/02 GCX Corp. Page 1 of 4
GCX Mounting Assembly Operation/Installation Manual
Dräger Model Cato
®
with Siemens SC9000 Patient Monitor
Patient Monitor – Left Side on Pivot Arm / Power Supply on Right Side
The purpose of these instructions is to:
1. Describe attachment of GCX mounting hardware to the Cato anesthesia machine.
2. Describe attachment of the Siemens monitor to the GCX mounting hardware.
WARNING
: USE OF MOUNTING HARDWARE AND MONITORING COMPONENTS OTHER THAN THOSE
DESCRIBED
IN
THIS
DOCUMENT MAY RESULT IN SERIOUS INJURY DUE TO TIPPING OF THE
ANESTHESIA
MACHINE.
THIS CATO MOUNTING CONFIGURATION REQUIRES THE 40KG COUNTERWEIGHT WITH
EXTENDED
WHEEL
ADAPTER
UPGRADE
SET FROM DRÄGER (PART NUMBER: 86 018 68)
Installer
: When installation is completed, provide these instructions to the end user for future reference.
INSTALLATION
Tools Required: Philips head screw driver, Hex key (incl.).
Mounting the Channel to Cato Edition
Parts Required: 4" Channel, M6 x 16 mm FHMS screws (2).
Brass
Plate
with
inserts
from
Dräger
(M29110)
1. To attach the Channel to the Cato left side accessory track,
locate the brass plate in the accessory track, align the
mounting holes in the Channel with the threaded holes on
the brass plate then run the M5 flat head screws (2) partly
in. (Note: Fixed Stop is at the bottom of the Channel)
2. Set the height of the Channel in the accessory track and
tighten the M6 screws to hold in place.
Prepare M Series Arm
1) Install the Tilt Limiting Stop screw.
M6 x 16 mm (2) FHMS
Accessory Track
Fixed Stop
5/16-18 x ½” SHCS (1)
"Loading the manual" means you need to wait until the file loads and becomes available for online reading. Some manuals are very large, and the time they take to appear depends on your internet speed.
Summary
DU-DR-0016-SC9000 Rev A 6/4/02 GCX Corp. Page 2 of 4 Install M Series Arm 1. The Slide has (2) ¼-20 x ¾” SHSS set screws that, when tightened, secure the Arm at the desired location within the Channel. 2. While supporting the bottom of the Arm with one hand, guide the Slide (at the rear of the arm) ...
DU-DR-0016-SC9000 Rev A 6/4/02 GCX Corp. Page 3 of 4 INSTRUCTIONS FOR USE – M Series Pivot Arm Pivot 1. To pivot the Arm (near the wall), simply push on the side of the Arm or mounted device. 2. To adjust the pivot tension at the Slide, use a ½” (or 13mm) socket driver to tighten or loosen the Pivot...
DU-DR-0016-SC9000 Rev A 6/4/02 GCX Corp. Page 4 of 4 Cleaning 1. The mounting assembly may be cleaned with most mild, non-abrasive solutions commonly used in the hospital environment (e.g. diluted bleach, ammonia, or alcohol solutions). 2. The surface finish will be permanently damaged by strong che...
