Page 2 - WARNING; • Crystalline silica from bricks, cement, and
WARNING Some dust created by power sanding, sawing, grind- ing, drilling, and other construction activities con- tains chemicals known to the State of California to cause cancer, birth defects or other reproductive harm. Some examples of these chemicals are: • Lead from lead-based paints. • Crystall...
Page 3 - CONTENTS
- 1 - ASSEMBLY OPERATIONS MAINTENANCE ELECTRICAL ADJUSTMENTS SAFETY INTRODUCTION CONTENTS INTRODUCTION............................................................................................. 2 About the W1669 and W1670 Radial Drill Presses ..........................................................
Page 5 - Specifications
- 3 - Motor Type: ...................................................... TEFC Capacitor Start Induction Motor: .............................................. 1⁄2 HP, 110V, 5 Amp., Single-Phase ⁄ 60 Hz RPM: .................................................................................................
Page 6 - NOTICE
- 4 - READ.MANUAL.BEFORE.OPERATING.MACHINE FAILURE.TO.FOLLOW.INSTRUCTIONS.BELOW.WILL. RESULT.IN.PERSONAL.INJURY 1.. Thoroughly.read.the.instruction.manual.before.operating.your.machine.. Learn the applications, limitations and potential hazards of this machine. Keep manual in a safe, convenient plac...
Page 9 - Grounding
- 7 - Ground.this.machine! The electrical cord sup- plied with the W1669 and W1670 Radial Drill Press comes with a grounding pin. DO.NOT remove the pin if your outlet does not accept a ground pin, see Figure.4 . Have the outlet box replaced by a qualified electrician or have an appropriate adapter i...
Page 14 - Headstock
-12- GET.help.to.lift.the.head- stock,. or. you. may. seri- ously. hurt. your. back. or. drop.the.headstock.. The headstock is secured with a set screw so it is aligned with the drill press base for balance and weight distribution. DO.NOT over tighten the set screw, or you will bend the column or st...
Page 15 - Spindle
-13- Drill.Chuck.and. Spindle Your keyed drill chuck attaches to the drill spindle. When properly joined, the JT-33 tapers on the spindle and inside the chuck cre- ate an almost permanent connection. To.install.the.drill.chuck,.do.these.steps: 1... Clean the drill chuck and spindle with min- eral sp...
Page 17 - Tension
-15- Figure.23. Typical spring cover lock slot and locking lug. Spring-Cover Lock Slot Locking Lug Figure.22.. Feed shaft return spring assembly. Spring Lock Cover Jam Nut and Cover Nut The feed shaft return spring is adjusted at the fac - tory; however, during the life of the drill press you may wa...
Page 19 - Table
-17- Table The table can be adjusted for height, rotation, and angle. The W1670 adds the fourth adjust - ment of table distance from column. Note: Table or table support parts are not interchangeable between the W1669 and the W1670 drill presses (see Figures.27.and.28 ). To.adjust.the.table,.do.thes...
Page 25 - Chart
Drill,.Cutter,.and.Hole.Saw.Suggested.RPM. Chart -23- .... .... .... .... .... .... .... . OPERATIONS
Page 30 - Parts
43 47 39 37 51 50 44 48 45 59 75 60 32 31 46 27 34 36 28 28A 28 42 41 40 33 20 64 65 66 54 38 53 22 23 93 36 19 5649 76 53 21 26 62 25 35 52 63 10 77 81 9 30 8 85 86 24 88 87 76 01 23 15 94 103 79 38-1 89 35-1 19-4 19-1 19-2 19-3 45A-3 45A-1 45A-2 16A-1 16A 11 19-6 19-5 32-1 102 107 105 104 107 106 ...
Page 31 - PARTS
MAINTENANCE -29- PARTS .REF. PART.#. .DESCRIPTION 8 X1669008 GEAR 9 XPR16M EXT RETAINING RING 9MM 10 XPN03M HEX NUT M8-1.25 11 X1668019 CLAMP BOLT M10-1.5 X 30 15 X1669015 KNOB BOLT M8-1.25 X 16 16A X1669016A MOUNT PLATE N/S 16A-1 X1669016A-1 MOTOR PLATE N/S 19 X1669019 MOTOR 1 ⁄ 2 HP, 110V 19-1 X16...
Page 36 - Accessories
SHOP FOX ® .Drill. Press. Vises use precision ground steel guide rods, smooth-action Acme threads, ground steel jaws, with fixed jaw V-grooves for holding round stock, and dovetailed ways where applicable. D2727 SHOP FOX ® (3" Basic Vise) D2728 SHOP FOX ® (4" Basic Vise) D2729 SHOP FOX ® (6&...
Page 38 - Notes
Page 40 - Warranty
Woodstock International, Inc. warrants all SHOP FOX ® machinery to be free of defects from work- manship and materials for a period of two years from the date of original purchase by the original owner. This warranty does not apply to defects due directly or indirectly to misuse, abuse, negligence o...
Page 41 - Warranty.Registration
Name ___________________________________________________________________________________Street __________________________________________________________________________________City _________________________ State ___________________________ Zip ________________________Phone # ______________________...