Sharp LC-52LE820E - Manual

What is the Menu? You need to call up the OSD to perform settings for the TV. The OSD for the settings is called “Menu”. The “Menu” enables various settings and adjustments. Basic operation Display the Menu screen Press @ and the “Menu” screen displays. Exit the Menu screen The operation will exit t...

Introduction Operation without a remote control unit This function is useful when there is no remote control unit within your reach. Press @- and the “Menu” screen displays. Press !s/r instead of a/b or Yl/k instead of c/d to select the item.Press #b to complete the setting. 12 3 About the guide dis...

Attaching the stand unit Before performing work, spread cushioning over the surface on which you will be laying the TV. This will prevent it from being damaged. CAUTION Attach the stand in the correct direction. Be sure to follow the instructions. Incorrect installation of the stand may result in th...

Using the remote control unit Inserting the batteries Before using the TV for the first time, insert two supplied “AAA” size alkaline batteries. When the batteries become depleted and the remote control unit fails to operate, replace the batteries with new “AAA” size batteries. Open the battery cove...

Initial installation overview Follow the steps below one by one when using the TV for the first time. Some steps may not be necessary depending on your TV installation and connection. Preparation Connect an antenna cable to the antenna terminal (Page 10). If necessary, insert a CA card into the CI s...

0 Before turning on the power    2 1  Standard DIN45325 plug (IEC 169-2) 75 q coaxial cable AC cord (product shape varies in some countries)Check that the MAIN POWER switch on the rear of the TV is turned on ( ; ). Cable clamp (bundle the cables with the clamp)     Place the TV close to the ...

Initial auto installation When the TV is powered on for the first time after purchase, the initial auto installation wizard appears. Follow the menus and make the necessary settings one after another. Confirm the following before turning on the power Is the antenna cable connected? Is the AC cord pl...

Quick guide Searching for cable broadcasts To change each item to the appropriate settings: Press a/b to select the menu, and then press ; . Scrambled stations [Yes] Search method [Channel] Start frequency Network ID [None] Symbol rate 1 Symbol rate 2 QAM modulation 1 QAM modulation 2 Reset Search s...

Quick guide Checking signal strength and channel strength (DVB-T/C) If you install a DVB-T/C antenna for the first time or relocate it, you should adjust the alignment of the antenna to receive a good reception while checking the antenna setup screen. Go to “Menu” > “Setup” > “View setting” &g...

Daily operation Switching on/off Turning on/off the power Turn on ( ; ) the MAIN POWER switch on the rear of the TV (Page 4).To turn on the TV, press <a on the TV or >a on the remote control unit. To turn off the TV, press <a on the TV or >a on the remote control unit. Turn off ( a ) the...

Watching TV Selecting an external video source Once the connection is made, press b to display the “INPUT” screen, and then press b or a/b to switch over to the appropriate external source with ; . NOTE You can also select an external video source from “CH list” > “INPUT”. • TV INPUT Switchable C...

Watching TV EPG EPG is a programme list that is displayed on the screen. With the EPG, you can check the schedule of DTV/RADIO/ DATA, view detailed information about them, tune to an event currently on-air. Useful settings for using EPG Basic setting View setting EPG If you want to use the EPG for d...

Selecting a programme using EPG Basic operation The illustrations on this page are explained using three digit services. Display/Close the EPG screen Press EPG . E Select Enter Back Exit AM PM Programme info. Search by genre Search by date Timer list NOTE You can also display the EPG screen from “Me...

Watching TV Display the timer list for TV programmes Press B . Refer to page 18 for the timer setup. Timer setup using EPG You can switch to a programme at a set time. Press EPG . Press a/b/c/d to select the programme you want to set, and then press ; . Back to EPG Watch No Programme info. Next Pres...

Teletext What is teletext? Teletext broadcasts pages of information and entertainment to specially equipped TV. Your TV receives teletext signals broadcast by a TV network, and decodes them into graphical format for viewing. News, weather and sports information, stock exchange prices and programme p...

0 Before connecting ... Be sure to turn off the TV and any devices before making any connections. Firmly connect a cable to a terminal or terminals. Carefully read the operation manual of each external device for possible connection types. This also helps you get the best possible audiovisual qualit...

SCART connection Example of connectable devices VCR DVD player/recorder EE   VCR Decoder SCART cable (supplied accessory)/Conversion cableSCART cable   NOTE In cases when the decoder needs to receive a signal from the TV, make sure to select the EXT 1 terminal to which the decoder is connected i...

VIDEO connection Example of connectable devices VCR DVD player/recorder Game console Camcorder EEEE You can use the EXT 2 terminal when connecting to a game console, camcorder, a DVD player/recorder or other device.  AV cable (supplied accessory)/Conversion cable  Audio connections Speaker/amplifi...

Controlling HDMI devices using AQUOS LINK What is AQUOS LINK? Using the HDMI CEC protocol, with AQUOS LINK you can interactively operate compatible system devices (AV amplifier, DVD player/recorder, Blu-ray player/ recorder) using a single remote control unit. NOTE AQUOS LINK-compatible AQUOS AUDIO ...

Connecting an AQUOS BD player/AQUOS recorder via the AQUOS AUDIO speaker system    AQUOS BD player/AQUOS recorder AQUOS AUDIO speaker system HDMI-certified cable  Optical audio cable  Connecting an AQUOS BD player/AQUOS recorder only  AQUOS BD player/AQUOS recorder The ARC (Audio Return Channe...

Operating an AQUOS LINK device AQUOS LINK allows you to operate the HDMI-connected device with a single remote control unit. Press I to start playback of a title. See the section Top menu/title list if you want to start playback using the list of the titles in the AQUOS BD player/AQUOS recorder. Pre...

Picture settings Go to “Menu” > “Setup” > “Picture”. Setup AV mode Picture OPC [Off] CH list :Back :Enter Menu Backlight Contrast Picture AV mode “AV mode” gives you several viewing options to choose from to best match the system environment, which can vary due to factors like room-brightness,...

Picture Advanced This TV provides various advanced functions for optimising the picture quality. Go to “Menu” > “Setup” > “Picture” > “Advanced”. C.M.S.-hue This function adjusts the hue of a selected colour using a six-colour adjustment system. C.M.S.-saturation This function increases or ...

Audio settings Go to “Menu” > “Setup” > “Audio”. Setup Bass Auto volume Audio Treble [Off] STANDARD CH list :Back :Enter Menu Balance L30 R30 Audio Auto volume Different sound sources sometimes do not have the same volume level, such as a programme and its commercial breaks. This function redu...

Power save settings Go to “Menu” > “Setup” > “ECO”. Setup No signal off ECO picture control ECO Energy save CH list :Back :Enter Menu No operation off [Disable] [Disable] [Off] [On] ECO ECO picture control This function automatically detects the image source and decreases the power consumption...

0 Channel settings Setup Quick start Auto installation View setting Channel settings CH list :Back :Enter Menu Individual setting View setting Auto installation The TV automatically detects and stores all available services in your area. This function also allows you to perform the channel setting f...

Basic adjustment Manual adjust Configure various settings for each service using the colour ( R / G / B ) buttons. Service no. Lock Service name Lock CH skip Old LCN CH skip Sort Delete Press a/b to select the desired service. Press the colour button on the remote control unit corresponding with the...

Analogue setting You can reconfigure the analogue TV channels settings automatically or manually. Additional search Use this menu to add new services automatically after “Analogue search” in the “Auto installation” menu has been completed. Start searching channels after selecting the colour system a...

Password/Lock settings View setting PIN Allows you to use a PIN to protect certain settings from being accidentally changed. Go to “Menu” > “Setup” > “View setting” > “Individual setting” > “PIN”. NOTE PIN input is required when executing “PIN”. The default PIN is “1234”. To clear the PI...

Basic adjustment Language settings View setting Digital audio language Set up to three preferred multi audio languages to display if the audio languages are available. Go to “Menu” > “Setup” > “View setting” > “Individual setting” > “Digital audio language”. Switching the multi audio lan...

Time shift This function enables you to pause the digital TV programme you are watching and start watching it again from the paused scene. This function is available only for the 820 model series. Press READY . The TV starts temporary recording of the real time broadcast in the background. Time shif...

Useful viewing functions Display information regarding time shift Channel display Channel information displays by pressing p on the remote control unit. Audio (ENG) STEREO Video Subtitle Off >> New information The time shift ready icon shows up when READY is pressed and the TV is recording the...

Selecting the picture size Selecting the WSS picture size automatically Option WSS The “WSS” allows the TV to switch automatically among the different picture size. Go to “Menu” > “Setup” > “Option” > “WSS”. NOTE Use “Wide mode” if an image does not switch to the appropriate picture size. W...

Selecting the recording picture size manually Option REC picture size You can use this menu to set the appropriate picture size for viewing a 16:9 format TV programme on a 4:3 TV. Go to “Menu” > “Setup” > “Option” > “Terminal setting” > “REC picture size”. Setting to “4:3 TV” Setting to ...

Display settings Channel display You can display the channel information by pressing p on the remote control unit. DTV mode ATV mode Audio (ENG) STEREO Video Subtitle Off >> New information MONO Auto Subtitle Four digit numbers (e.g., 0001) are displayed after selecting the five Nordic countri...

0 Setting when using external devices Input source settings Option Input select For setting the signal type of external equipment. Press b to select the input source for setting the input signal (“EXT 1” or “EXT 3”) from the “INPUT” menu, and then press ; . Go to “Menu” > “Setup” > “Option” &g...

Additional features Option Colour system You can change the colour system to one that is compatible with the image on the screen. Go to “Menu” > “Setup” > “Option” > “Colour system”. NOTE The factory preset value is “Auto”. If “Auto” is selected, the colour system for each channel is automa...

Photo mode Viewing thumbnails This bar is not shown in the “Home network” screen. Buttons for thumbnail operations Buttons Description ; When selecting a folder icon: Enter this directory. When selecting a photo thumbnail: Enlarge the photo. a/b/c/d (Cursor) Select a desired item. 6 Return to the pr...

Other useful features View setting DivX® setup This is the function to confirm your registration code. You need to register the code at www.divx.com. Go to “Menu” > “Setup” > “View setting” > “DivX® setup”. DivX® VOD registration You can find your registration code on this menu. You need to...

Connecting a PC HDMI connection PC HDMI 1, 2, 3 or 4  HDMI-certified cable  PC HDMI 2*   ø 3.5 mm stereo minijack cable  DVI/HDMI cable  When using the HDMI 2 terminal, you must select the proper item in the “Audio select” menu depending on the type of HDMI cable connected (refer to page 28 fo...

Adjusting the PC image automatically Option Auto sync. This function enables the screen to be automatically adjusted to its best possible condition when the analogue terminals of the TV and PC are connected with a commercially available DVI/RGB conversion cable, etc. Press b to select “EXT 3” from t...

RS-232C port specifications PC control of the TV When a programme is set, the TV can be controlled from the PC using the RS-232C terminal. The input signal (PC/video) can be selected, the volume can be adjusted and various other adjustments and settings can be made, enabling automatic programmed pla...

0 Troubleshooting Problem Possible solution No power. • Turn on ( ; ) the MAIN POWER switch on the rear of the TV (Page 4). Is the AC cord disconnected?Check if you pressed <a on the TV. ••• The TV cannot be operated. • External influences such as lightning, static electricity, etc., may cause im...

Updating your TV via DVB-T Ensure that your TV software version is always up to date. From time to time SHARP will make updated TV base software and DVB software available. View setting Download setup Go to “Menu” > “Setup” > “View setting” > “Individual setting” > “Standby search” > ...

Appendix Updating your TV via USB Information Software update This function allows you to update to the latest software using a USB device. You must update the software through the USB terminal. To check the software version for the TV, use the URL shown on the back cover. Go to “Menu” > “Setup” ...

Appendix Information on the software license for this product Software composition The software included in this product is comprised of various software components whose individual copyrights are held by SHARP or by third parties. Software developed by SHARP and open source software The copyrights ...

Specifications Item LCD COLOUR TV (40 o /81.28 cm), LC-40LE820E, LC- 40LE810E LCD COLOUR TV (46 o /116.84 cm), LC-46LE820E, LC- 46LE810E LCD COLOUR TV (52 o /132.08 cm), LC- 52LE820E LCD panel Advanced Super View & BLACK TFT LCD (40 o /81.28 cm) Advanced Super View & BLACK TFT LCD (46 o /116...

Environmental specifications Item 40 inch models 46 inch models 52 inch models I On-Mode (W) (HOME MODE) 71 W 85 W 96 W J Energy-Save-Mode (W) Advanced 69 W 77 W 86 W K Standby-Mode (W) 0.20 W 0.20 W 0.20 W L Off Mode (W) MAIN POWER switch 0.01 W or less 0.01 W or less 0.01 W or less M Annual Energy...

Appendix Dimensional drawings LC-52LE820E LC-46LE820ELC-40LE820E ( 1127.0 ) / [ 993.0 ]( 1127,0 ) / [ 993,0 ] ( 540.0 ) ( 540,0 )[ 450.0 ] [ 450,0 ] ( 785.0 ) / [ 707.0 ] ( 785,0 ) / [ 707,0 ] ( 400.0 ) / [ 300.0 ] ( 400,0 ) / [ 300,0 ] ( 734.0 ) / [ 659.0 ] ( 734,0 ) / [ 659,0 ] [ 404.0 ] [ 404,0 ]...

LC-40LE820E LC-40LE810E LC-46LE820E LC-46LE810E LC-52LE820E LCD COLOUR TELEVISIONLCD-FARBFERNSEHGERÄTTÉLÉVISEUR COULEUR À ÉCRANCRISTAUX LIQUIDES (LCD)TELEVISORE A COLORI LCDLCD-KLEURENTELEVISIETELEVISIÓN EN COLOR LCDTELEVISOR DE CRISTAL LÍQUIDOLCD RENKL İ TELEV İ ZYON КОЛЬОРОВИЙ ТЕЛЕВІЗОР З РІДКОКРИ...