Schneider Electric EM4000 - Manual

Schneider Electric EM4000

Schneider Electric EM4000 – Manual, read for free online in PDF format. We hope this helps you resolve any issues you may have. If you have further questions, please contact us through the contact form.

1 Page 1
2 Page 2
3 Page 3
4 Page 4
5 Page 5
6 Page 6
7 Page 7
8 Page 8
9 Page 9
10 Page 10
11 Page 11
12 Page 12
13 Page 13
14 Page 14
15 Page 15
16 Page 16
17 Page 17
18 Page 18
19 Page 19
20 Page 20
21 Page 21
22 Page 22
23 Page 23
24 Page 24
25 Page 25
26 Page 26
27 Page 27
28 Page 28
29 Page 29
30 Page 30
31 Page 31
32 Page 32
33 Page 33
34 Page 34
35 Page 35
36 Page 36
37 Page 37
38 Page 38
39 Page 39
40 Page 40
41 Page 41
42 Page 42
43 Page 43
44 Page 44
Page: / 44

Table of Contents:

  • Page 3 – Safety Information; Important Information; DANGER; WARNING; result in death or serious injury.; CAUTION; result in minor or moderate injury.; NOTICE; alert symbol shall not be used with this signal word.
  • Page 4 – Notices; FCC Part 15 Notice; receiver is connected.; FCC Part 68 Notice
  • Page 5 – There are no user serviceable parts in this equipment.; Network Compatibility Notice for the Internal Modem
  • Page 7 – Table of Contents
  • Page 9 – Introduction; System Description; PowerLogic EM4000 series System Specifications; The PowerLogic EM4000 series system architecture includes:
  • Page 10 – Table 1: PowerLogic EM4000 series; meter specifications
  • Page 11 – Front Panel Display; LCD; — displays 2 rows of 16 characters for each of the meter points (8, 12, or; Display button; — cycles through the available information for each of the; Left and right arrow buttons; — selects which of the meter points is on the; Figure 1: PowerLogic EM4080 front panel
  • Page 12 – Figure 2: PowerLogic EM4033 and PowerLogic EM4080 internal view
  • Page 13 – Safety Precautions; Carefully observe these safety instructions.; Electrical Standards Compliance; HAZARD OF ELECTRIC SHOCK, EXPLOSION, OR ARC FLASH
  • Page 14 – Installation; Receiving
  • Page 15 – label on the top right side of the unit.; Access to Power and Lighting; Installation Procedures; on page 9; “Connecting the Ethernet Cable” on page 25; Mounting the PowerLogic EM4000 meter; each mounting keyhole and tightening the screws.
  • Page 16 – Figure 3: 120V Mounting Layout, Dimensions and Clearances
  • Page 18 – Figure 4: Typical three-phase 347V installation; Shorting block detail
  • Page 19 – • see “For a 600Y/347V or higher three-phase wye panel with potential
  • Page 21 – For a single-phase panel with the 120V variant of the meter:
  • Page 23 – FROM PANEL
  • Page 24 – with the 120V variant of the meter:; NOTE: For the wiring of the potential transformers, see Figure 4.
  • Page 25 – Delta service metering
  • Page 26 – Installing the Current Transformers
  • Page 27 – D A N G E R
  • Page 28 – Figure 11: PowerLogic EM4080 mA current transformer
  • Page 29 – NOTE: The direction of the energy flow is indicated on the CT.; Installing 5A Converters and CTs on the PowerLogic EM4080
  • Page 30 – on the shorting device.
  • Page 31 – Figure 12: PowerLogic EM4080 5A CT connection to converter
  • Page 32 – Table 2: PowerLogic EM4000 meter CT color pair identification
  • Page 33 – Connecting the Communications; Connecting the Ethernet Cable; network as shown in Figure 13, set the DIP switches as follows:; Figure 13: Modbus wiring diagram
  • Page 34 – Connecting Pulse Inputs; Connect the output of the pulsing device to one of the two; pulse input; terminal; pulse in; operating status of the unit as follows:; Initial power up message “PowerLogic EM4000”; Manually Testing Communications; appears on the display.; program default IP addresses.
  • Page 35 – Display Navigation; Diagnostics Mode
  • Page 36 – Recording the Meter Map
  • Page 38 – Maintenance; Fuse Replacement; Figure 15: Replacing the fuse; Apply appropriate personal protective equipment (PPE) and follow
  • Page 39 – Regulatory Compliance; Table 3: Regulatory Compliance; Equipment servicing and access; Access to equipment; Table 4 shows the graphical symbols that appear on the equipment.
  • Page 40 – Table 4: Graphical symbols that appear on equipment
  • Page 41 – English; Index; Numerics
Loading the manual

PowerLogic

TM

Series EM4000

High-Density Meter Installation Guide

930-134-01-A.00
11/2013

"Loading the manual" means you need to wait until the file loads and becomes available for online reading. Some manuals are very large, and the time they take to appear depends on your internet speed.

Summary

Page 3 - Safety Information; Important Information; DANGER; WARNING; result in death or serious injury.; CAUTION; result in minor or moderate injury.; NOTICE; alert symbol shall not be used with this signal word.

Safety Information Important Information Read these instructions carefully and look at the equipment to become familiar with the device before trying to install, operate, service or maintain it. The following special messages may appear throughout this manual or on the equipment to warn of potential...

Page 4 - Notices; FCC Part 15 Notice; receiver is connected.; FCC Part 68 Notice

Notices FCC Part 15 Notice This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment gene...

Page 5 - There are no user serviceable parts in this equipment.; Network Compatibility Notice for the Internal Modem

telephone company will notify you as soon as possible. You will also be advised of your right to file a complaint with the FCC if you believe it is necessary. The telephone company may make changes in its facilities, equipment, operations or procedures that could affect the operation of this equipme...

Other Schneider Electric Models

All Schneider Electric Other