Rotel FR01773 - User Manual

Page 2 - A12MKII Stereo Integrated Amplifier; Notice; Important Safety Instructions

2 A12MKII Stereo Integrated Amplifier You must allow a minimum 10 cm or 4 inches of unobstructed clearance around the unit. WARNING: The rear panel power cord connector is the mains power disconnect device. The device must be located in an open area that allows access to the cord connector.The unit ...

Page 3 - Органы управления и разъемы; r t y u

3 Figure 1: Controls and Connections Commandes et Branchements Bedienelemente und Anschlüsse Controles y Conexiones Controlli e connessioni De bedieningsorganen en aansluitingen Kontroller och anslutningar Органы управления и разъемы E POWER PHONES PHONO TUNER CD USB OPT COAX AUX PC-USB BT 5V / 2.1A...

Page 5 - Подсоединение источников сигнала и акустических систем

5 Figure 3: Preamp Input and Speaker Output Connections Branchements des entrées sources et sorties enceintes acoustiques Anschlussdiagramm Conexiones para Entrada de Señal y Salida a las Cajas Acústicas Collegamenti ingressi e diffusori De signaalingangen en de luidsprekeruitgangen Signal- och högt...

Page 7 - Подсоединение 12-В триггерного сигнала

7 Figure 5: 12V Trigger Connections Branchements trigger 12 V 12V-Trigger-Anschlüsse Conexiones para Señal de Disparo de 12V De 12V trigger aansluitingen Collegamenti segnali Trigger 12 V 12 V-anslutning för styrsignal Подсоединение 12-В триггерного сигнала CLASS 1LASER PRODUCT APPAREIL LASER DE CLA...

Page 8 - Важные замечания

8 A12MKII Stereo Integrated Amplifier Important Notes When making connections be sure to: 4 Turn off all the components in the system before hooking up any components, including loudspeakers. 4 Turn off all components in the system before changing any of the connections to the system. It is also rec...

Page 10 - The RR-AX1400 Remote Control

10 A12MKII Stereo Integrated Amplifier A Few Precautions WARNING: To avoid potential damage to your system, turn off ALL the components in the system when connecting or disconnecting the loudspeakers or any associated components. Do not turn the system components back on until you are sure all the c...

Page 11 - Protection Indicator; Input Signal Connections; Preamp Output; Speaker Outputs

11 Protection Indicator 2 The amplifier has both thermal and over-current protection circuitry that protects the amplifier against damage in the event of extreme or faulty operating conditions. The protection circuits are independent of the audio signal and have no impact on sonic performance. Inste...

Page 12 - Headphone Output; Volume Control; Source Input Selector

12 A12MKII Stereo Integrated Amplifier If you are using terminal lugs, connect them to the wires. If you are attaching bare wires directly to the binding posts, separate the wire conductors and strip the insulation from the end of each conductor. Be careful not to cut into the wire strands. Unscrew ...

Page 13 - Dimmer Control; Display Dimmer; Rotel Link

13 Dimmer Control Display Dimmer 9 D To change the brightness of the front display, press the MENU 9 button to toggle to the DIMMER Setting. Then press the - or + buttons on the front panel to change the display brightness. NOTE: This setting is saved permanently including after powering off the A12...

Page 15 - Troubleshooting; Power Indicator Is Not Illuminated

15 Troubleshooting Most difficulties in audio systems are the result of incorrect connections, or improper control settings. If you encounter problems, isolate the area of the difficulty, check the control settings, determine the cause of the fault and make the necessary changes. If you are unable t...

Page 16 - Specifications

16 A12MKII Stereo Integrated Amplifier Specifications Maximum Power Output Maximum Power Output 120 watts/ch, 4 Ohms Continuous Power Output Continuous Power Output 60 watts/ch, 8 Ohms Total Harmonic Distortion Total Harmonic Distortion < 0.018% Intermodulation Distortion Intermodulation Distorti...

Rotel FR01773 - User Manual

Table of Contents:

Summary

Other Rotel Amplifiers Models