Rotel FR01266 - Manuals - manualsarea.com

Page 2 - A14MKII Stereo Integrated Amplifier; Notice; Important Safety Instructions

2 A14MKII Stereo Integrated Amplifier You must allow a minimum 10 cm or 4 inches of unobstructed clearance around the unit. WARNING: The rear panel power cord connector is the mains power disconnect device. The device must be located in an open area that allows access to the cord connector.The unit ...

Page 3 - Органы управления и разъемы; r t y u

3 Figure 1: Controls and Connections Commandes et Branchements Bedienelemente und Anschlüsse Controles y Conexiones Controlli e connessioni De bedieningsorganen en aansluitingen Kontroller och anslutningar Органы управления и разъемы POWER PHONES A14MKII PHONO TUNER CD USB OPT COAX AUX PC-USB BT 5V ...

Page 4 - Mando a Distancia RR-AX1400

4 A14MKII Stereo Integrated Amplifier A B C D E F GH I N L K J M Figure 2: Remote Control RR-AX1400 Télécommande infra-rouge RR-AX1400 Fernbedienung RR-AX1400 Mando a Distancia RR-AX1400 Telecomando RR-AX1400 De afstandsbediening RR-AX1400 Fjärrkontroll RR-AX1400 Пульт ДУ RR-AX1400

Page 5 - Подсоединение источников сигнала и акустических систем; Amplifier A14MKII

5 Figure 3: Preamp Input and Speaker Output Connections Branchements des entrées sources et sorties enceintes acoustiques Anschlussdiagramm Conexiones para Entrada de Señal y Salida a las Cajas Acústicas Collegamenti ingressi e diffusori De signaalingangen en de luidsprekeruitgangen Signal- och högt...

Page 7 - Подсоединение 12-В триггерного сигнала

7 Figure 5: 12V Trigger Connections Branchementstrigger 12 V 12V-Trigger-Anschlüsse Conexiones para Señal de Disparo de 12V T14 NETWORK TUNER R ANTENNA FM DAB L OUTPUT COAXIAL OUT USB RS232 12V TRIGGER IN OUT OUT ROTEL LINK OUT WIFI ANTENNA WIFI ANTENNA Amplifier A14MKII Tuner T14 De 12V trigger aan...

Page 8 - Важные замечания

8 A14MKII Stereo Integrated Amplifier Important Notes When making connections be sure to: 4 Turn off all the components in the system before hooking up any components, including loudspeakers. 4 Turn off all components in the system before changing any of the connections to the system. It is also rec...

Page 10 - The RR-AX1400 Remote Control

10 A14MKII Stereo Integrated Amplifier A Few Precautions WARNING: To avoid potential damage to your system, turn off ALL the components in the system when connecting or disconnecting the loudspeakers or any associated components. Do not turn the system components back on until you are sure all the c...

Page 11 - Preamp Output; Speaker Outputs

11 Protection Indicator 2 The amplifier has both thermal and over-current protection circuitry that protects the amplifier against damage in the event of extreme or faulty operating conditions. The protection circuits are independent of the audio signal and have no impact on sonic performance. Inste...

Page 12 - Volume Control

12 A14MKII Stereo Integrated Amplifier If you are using terminal lugs, connect them to the wires. If you are attaching bare wires directly to the binding posts, separate the wire conductors and strip the insulation from the end of each conductor. Be careful not to cut into the wire strands. Unscrew ...

Page 13 - Source Input Selector; Dimmer Control; Display Dimmer; Rotel Link

13 sparingly. Be particularly careful when turning the controls up. This increases the power output in the bass or treble range, increasing the load on the amplifier and speakers. NOTE: Setting the Bass and Treble controls do not automatically turn on the tone control. To turn on tone control, refer...

Page 14 - Settings Menu

14 A14MKII Stereo Integrated Amplifier Settings Menu You can access the SETUP menu from the front panel by pressing the MENU 9 button or the K button on the remote. You can change the value of the selected option by pressing the - or + buttons on the front panel or the up/down/left/right C arrow but...

Page 15 - Troubleshooting; Power Indicator Is Not Illuminated

15 • COAX1 VOL: VARIABLE (disabled) is factory default. • COAX2 VOL: VARIABLE (disabled) is factory default. • BTOOTH VOL: VARIABLE (disabled) is factory default. NOTE: The Volume knob on the front panel and Volume +/- buttons on the IR remote are disabled when the volume is Fixed. To disable this f...

Page 16 - No Sound; Specifications

16 A14MKII Stereo Integrated Amplifier No Sound Check the signal source to see if it is functioning properly. Make sure the cables from the signal source to the amplifier inputs are connected properly. Be sure the Input Source is set to the proper input. Check the wiring between the amplifier and th...