POSIFLEX PD-7100 - Manual - manualsarea.com

Page 2 - SOME IMPORTANT NOTES; FCC NOTICE; TRADE MARKS AND SERVICE MARKS

P/N: 19440900020 SOME IMPORTANT NOTES FCC NOTICE This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions manual, may cause interference to radio communications. It has been tested and found to comply with limits for a ...

Page 3 - TABLE OF CONTENTS

i TABLE OF CONTENTS GENERAL DESCRIPTION · · · · · · · · · · · · · · · · · · · · · 1 - 1 Introduction · · · · · · · · · · · · · · · · · · · · · · · · · 1 - 1 Application · · · · · · · · · · · · · · · · · · · · · · · · · · 1 - 1 Special Features · · · · · · · · · · · · · · · · · · · · · · · 1 - 1 Desc...

Page 4 - OPTICAL CHARACTERISTICS; ENVIRONMENTAL CHARACTERISTICS

ii Normal Operation Ratings · · · · · · · · · · · · · · · · · · 5 - 1 OPTICAL CHARACTERISTICS · · · · · · · · · 5 - 1 Character Format · · · · · · · · · · · · · · · · · · · · · · 5 - 1 Fundamental Specification · · · · · · · · · · · · · · · · · · 5 - 2 ENVIRONMENTAL CHARACTERISTICS · 5 - 2

Page 5 - DESCRIPTION

1 - 1 I. GENERAL DESCRIPTION A. Introduction This documentation describes the features and requirements of the product series of PD-7100 / 7200, a Liquid Crystal Display which is a wide customer display. It displays alphanumerical characters in 2 lines of 20 large sized characters and is able to dis...

Page 8 - A. Signal connection; Using power adaptor

3 - 1 III. INSTALLATION A. Signal connection Connect the DB9 female connector of the signal cable CCBLA - 372 to the COM port of the host computer or POS system and connect the DB9 male connector of the signal cable CCBLA – 372 to the DB9 female connector in the base of the PD. B. Power connection 1...

Page 10 - C. Connect for Pass Through Operation

3 - 3 3. Using power from POS system This super convenient power supply method applies only when connected to a Posiflex POS system after proper setting for power in COM port. The power connection is already done when the signal connection is completed. 4. Using printer power adaptor The PD-7100/720...

Page 11 - D. After Powering Up

3 - 4 Please reserve the COM port terminator in a safe place in case the non-pass-through operation would be required in the future. D. After Powering Up A firmware version as power on sign will appear on the screen for a while and the emulation mode will appear for a while after the firmware versio...

Page 12 - On control board in display head

3 - 5 C. Dip Switch & Jumper Settings 1. On control board in display head Emulation mode (reach the switches from outside of back of the head) SW2 SW1 OFF ON OFF EPSON 2 X 20 NORITAKE 2 X 20 ON EPSON 4 X 26 IEE (CHINESE) 2 X 10 RS232 protocol (Inside display head) Short Open JP1 19200, n, 8, 1 9...

Page 14 - SPECIFICATIONS; A. Mechanical Drawings

4 - 1 V. MECHANICAL SPECIFICATIONS A. Mechanical Drawings B. Mechanical Function The pole of this customer display consists of 2 sections enabling adjustment on the height of the pole. The total height of this display is dependent on the pole adjustment, please refer to the drawings of last section ...

Page 15 - CHARACTERISTICS; B. Interface Signals; VII. OPTICAL CHARACTERISTICS

5 - 1 VI. ELECTRICAL CHARACTERISTICS A. Power ON / OFF Sequence There are no deleterious effects associated with power ON and OFF of this display; however, rapid ON / OFF sequencing is not recommended. Neither data nor power connectors should be connected / disconnected while power is applied. B. In...

Page 16 - B. FUNDAMENTAL SPECIFICATION

5 - 2 B. FUNDAMENTAL SPECIFICATION Number of display dot : 160 x 32 Effective display area : 179.15 (W) x 36.75 (H) mm Dot size : 1.07 (W) x 1.10 (H) mm LCD type : STN with backlight Viewing angle : 80 degrees vertically, 60 degrees horizontally Response time : 250 ms (typical) VIII. ENVIRONMENTAL C...

POSIFLEX PD-7100 - Manual

Table of Contents:

Summary

Other POSIFLEX Models