POSIFLEX LS-1000 - Manual
POSIFLEX LS-1000 – Manual, read for free online in PDF format. We hope this helps you resolve any issues you may have. If you have further questions, please contact us through the contact form.
Table of Contents:
- Page 2 – Fig. 2 RJ45 Type Modular Plug
- Page 3 – USING THE SCANNER; SCANNER INTRODUCTION; Features
- Page 5 – Scan Test; window of a text editor, try to scan several known-good barcodes.; Reset to Default Status; programming codes section.
- Page 7 – SCANNER OPERATION; Operating the Scanner; Ensure the scan line crosses every bar and space of the symbol; Omni-Directional Scan Mode; The scanner will always stay active in
- Page 9 – SCANNER MAINTANTENCE; Maintaining the Scanner; TROUBLE SHOOTING GUIDE
- Page 11 – PROGRAMMING CODES; All framed barcode names represent as default settings.; Abort; The reading of the “ ABORT” label
- Page 12 – The reading of the “ RESET”; Return to USB default
- Page 14 – Codabar Enable
FCC Notes:
This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions manual,
may cause interference to radio communications. It has been tested and found to comply with limits for a Class A digital device pursuant to EN55022 and 47
CFR, Part 2 and subpart J of Part 15 of FCC Rules, which are designed to provide reasonable protection against interference when operated in a commercial
environment. Operation of this equipment in a residential area is likely to cause interference in which case the user at his own expense will be required to
take whatever measures to correct the interference.
For CE-countries:
This scanner is in conformity with CE standards. Please note that an approved, CE-marked power supply unit should be used in order to
maintain CE conformance.
Laser Safety:
The laser scanner complies with safety standard IEC 60825 –1 for a Class I laser produce. It also complies with CDRH as applicable to a
Class IIa laser product. Avoid long term staring into direct laser light.
Radiant Energy:
The laser scanner uses one low-power visible laser diodes operating at 650nm in an opto-mechanical scanner resulting in less than 3.9
μ
W
radiated power as observed through a 7mm aperture and averaged over 10 seconds.
Do not attempt to remove the protective housing of the scanner, as unscanned laser light with a peak output up to 0.8mW would be accessible inside.
Laser Light Viewing:
The scan window is the only aperture through which laser light may be observed from this product. A failure of the scanner motor,
while the laser diode continues to emit a laser beam, may cause emission levels to exceed those for safe operation. The scanner has safeguards to prevent
this occurrence. If, however, a stationary laser beam is emitted, the failing scanner should be disconnected from its power source immediately.
Adjustments:
Do not attempt any adjustments or alteration of this product. Do not remove the protective housing of the scanner. There are no user-
serviceable parts inside.
Caution:
Use of controls or adjustments or performance of procedures other than those specified herein may result in hazardous laser light exposure.
Optical:
The use of optical instruments with this product will increase the eye hazard. Optical instruments include binoculars, magnifying glasses, and
microscopes but do not include normal eye glasses worn by the user.
Warranty Limits:
Warranty terminates automatically when any person other than the authorized technicians opens the machine. The user should consult
his/her dealer for the problem happened. Warranty voids if the user does not follow the instructions in application of this merchandise. The manufacturer is
by no means responsible for any damage or hazard caused by improper application.
No part of this document may be reproduced, transmitted, stored in a retrieval system, transcribed, or translated into any language or
computer language in any form or by any means electronic, mechanical, magnetic, optical, chemical, manual or otherwise, without express
written consent and authorization.
We reserve the right to make changes in product design without reservation and without notification. The material in this guide is for
information only and is subject to change without notice.
All trademarks mentioned herein, registered or otherwise, are the properties of their various respective owners.
About This Manual:
Posiflex Technologies, Inc. has made every effort for the accuracy of the content in this manual. However, Posiflex Technologies, Inc. will assume no
liability for any technical inaccuracies or editorial or other errors or omissions contained herein, nor for direct, indirect, incidental, consequential or
otherwise damages, including without limitation loss of data or profits, resulting from furnishing, performance, or use of this material.
This information is provided “as is ” and Posiflex Technologies, Inc. expressly disclaims any warranties, expressed, implied or statutory, including without
limitation implied warranties of merchantability or fitness for particular purpose, good title and against infringement.
The information in this manual contains only essential hardware concerns for general user and is subject to change without notice. Posiflex Technologies,
Inc. reserves the right to alter product designs, layouts or drivers without notification. The system integrator shall provide applicative notices and
arrangement for special options utilizing this product. The user may find the most up to date information of the hardware from: http://www.posiflex.com or
http://www.posiflex.com.tw or http://www.posiflexusa.com
All data should be backed-up prior to the installation of any drive unit or storage peripheral. Posiflex Technologies, Inc. will not be responsible for any loss
of data resulting from the use, disuse or misuse of this or any other Posiflex product.
All rights are strictly reserved. No part of this documentatio n may be reproduced, stored in a retrieval system, or transmitted in any form or by any means,
electronic, mechanical, photocopying, or otherwise, without prior express written consent from Posiflex Technologies, Inc. the publisher of this
documentation.
©
Copyright Posiflex Technologies, Inc. 200 9
All brand and product names and trademarks are the property of their respective holders.
LS-1000 Series
Laser Barcode Scanner
User’s Manual
Rev. A0
P/N: 18050900030
Page 1
"Loading the manual" means you need to wait until the file loads and becomes available for online reading. Some manuals are very large, and the time they take to appear depends on your internet speed.
Summary
FUNDAMENTAL INFORMATION MODEL NAME: LS-1000 CONTENT ( Besides this guide) : Fig. 1 Box content besides this guide INSTALLATION GUIDES 1. Install the USB or RS232 interface cable onto the scanner by inserting the 8 pin RJ45 type modular plug ( Fig. 2 ) of the cable into the scanner until a firm click...
Description Function Scan Window Reads barcodes Object Detector Trigger and wake up scanner automatically whenpresented with barcode in its range Beeper Hole For beep tone indication USING THE SCANNER SCANNER INTRODUCTION Features The scanner unit is a compact and space-saving hands-free omni-direct...
SCANNER SETUP (PROGRAMMING) In most of the cases no setup is required. The default setup of the scanner makes the scanner able to detect automatically the most commonly applied bar code types as tabulated above and send the data to the host system as if they are read from an USB or RS232 keyboard. T...
