Porter-Cable FN250A - Manual

Page 2 - GB; ENGLISH

2 PORTER ✦✦ CABLE Porter-Cable Corporation4825 Highway 45 NorthJackson, TN 38305 Date of Manufacture: ___________________________ Fecha de fabricación:, Date de fabrication: Serial No: ______________________________________ Número de serie:, Nombre d'ordre GB ENGLISH EC-DECLARATION OFCONFORMITY W e ...

Page 3 - SAFETY GUIDELINES / DEFINITIONS; SAVE THESE INSTRUCTIONS!; IMPORTANT SAFETY INSTRUCTIONS; Improper operation or maintenance of this product could

3 indicates an imminently hazardous situation which, if not avoided, will result in death or serious injury. indicates a potentially hazardous situation which, if not avoided, could result in death or serious injury. indicates a potentially hazardous situation which, if not avoided, may result in mi...

Page 4 - GENERAL SAFETY RULES

4 1. Read and understand tool labels andmanual. Failure to follow warnings could result in DEATH or SERIOUS INJURY . Fig. 1. 2 . Operator and others in work area MUST wear safety glasses with side shields. These safety glasses must conform to ANSIZ87.1 requirements (approved glasses have“Z87” printe...

Page 6 - TECHNICAL SPECIFICATIONS

6 21. Remove finger from trigger when not driving fasteners. Never carry tool with fingeron trigger. In “Contact Actuation Mode” toolwill fire a fastener if safety is bumped whiletrigger is depressed. Fig. 14. 22. Do not overreach. Keep proper footing a n d b a l a n c e a t a l l t i m e s w h e n ...

Page 7 - EMPLOYER’S RESPONSIBILITIES

7 Employer must enforce compliance with the safety warnings and all other instructions contained in this manual. Keep this manual available for use by all people assigned to use this tool. For personal safety and proper operation of this tool, read and understandtool labels and manual. Failure to fo...

Page 8 - Never point tool at yourself or others.

8 Never point tool at yourself or others. Always connect tool to air supply before loading fasteners (Fig. 18).Do not load fasteners with trigger or safety depressed.Only use approved Porter-Cable fasteners.Operator and others in work area MUST wear safety glasses with side shields. Always wear ANSI...

Page 9 - FASTENER GUIDE; m u s t; USING THE TOOL; OPERATING INSTRUCTIONS

9 FASTENER GUIDE A Fastener Guide (A) Fig. 23 and 24,i s f a c t o r y i n s t a l l e d o n M o d e lFN250A. The Guide is held in placewith a bolt and nut (B) Fig. 23 and2 4 . T h e F a s t e n e r G u i d e m u s t b e used whenever driving fasteners thatare less than 1 1 / 2 " long. The Faste...

Page 10 - Do Not; CLEARING A JAMMED FASTENER

10 Remove finger from trigger when not driving fasteners. Never carry tool with finger on trigger: tool will fire a fastener if safety is bumped. Keep fingers AWAY from trigger when not driving fasteners to avoid accidental firing. Never carry tool with finger on trigger. In “Contact Actuation Mode”...

Page 11 - CLEAN AND INSPECT DAILY; D i s c o n n e c t t o o l f r o m a i r s u p p l y b e f o r e c l e a n i n g a n d; SERVICE AND REPAIRS; Disconnect tool from air supply before performing any Service; MAINTENANCE

11 CLEAN AND INSPECT DAILY D i s c o n n e c t t o o l f r o m a i r s u p p l y b e f o r e c l e a n i n g a n d inspection. Correct all problems before placing the tool back in use. Wipe tool clean and inspect for wear or damage. Use non-flammablecleaning solutions to wipe exterior of tool only i...

Page 12 - ACCESSORIES

12 2. Tool does nothing or Inadequate air supply. Verify adequate air supply. operates sluggishly. Inadequate lubrication. Put 5 or 6 drops of oil into air inlet. Worn or damaged Install Overhaul Kit. o-rings or seals. 3. Air leak near bottom Loose screws. Tighten screws. of tool. Worn or damaged In...

Porter-Cable FN250A - Manual

Table of Contents:

Summary

Other Porter-Cable Models