Porter-Cable 750 - Manual - manualsarea.com

Page 3 - CALIFORNIA PROPOSITION 65; SAFETY GUIDELINES - DEFINITIONS

3 Some dust created by power sanding, sawing, grinding, drilling, and other construction activities contains chemicals known (to the State of California) to cause cancer, birth defects or other reproductive harm. Some examples of these chemicals are: ● lead from lead-based paints ● crystalline silic...

Page 4 - GENERAL SAFETY RULES

4 R e a d a l l i n s t r u c t i o n s . F a i l u r e t o f o l l o w a l l instructions listed below may result in electric shock, fire and/or serious injury. The term "power tool" in all of the warnings listed below refers to your mains-operated (corded) power tool or battery-operated (c...

Page 6 - ADDITIONAL SPECIFIC SAFETY RULES

6 ADDITIONAL SPECIFIC SAFETY RULES 1. Hold power tool by insulated gripping surfaces when performing an operation where the cutting tool may contact hidden wiring or its own cord. Contact with a "live" wire will make exposed metal parts of the tool "live" and shock the operator. 2. U...

Page 7 - IPXX; SAVE THESE INSTRUCTIONS!; MOTOR

7 SYMBOL DEFINITION V ........................ volts A ........................ amperes Hz ........................ hertz W ........................ watts kW ........................ kilowatts F ........................ farads µ F ........................ microfarads l ........................ litre...

Page 8 - FUNCTIONAL DESCRIPTION; such as plastics, fiberglass and hard rubber.; EXTENSION CORD SELECTION

8 Length of Cord in Feet 115V 25 Ft. 50 Ft. 100 Ft. 150 Ft. 200 Ft. 250 Ft. 300 Ft. 400 Ft. 500 Ft. 230V 50 Ft. 100 Ft. 200 Ft. 300 Ft. 400 Ft. 500 Ft. 600 Ft. 800 Ft. 1000 Ft. 0-2 18 18 18 16 16 14 14 12 12 2-3 18 18 16 14 14 12 12 10 10 3-4 18 18 16 14 12 12 10 10 8 4-5 18 18 14 12 12 10 10 8 8 5-...

Page 9 - with Keyless; NOTE; OPERATION

9 SELECTING THE BLADE For best performance, longer blade life, and smoother cut, select the properblade for the job. When cutting metal always select a blade which will allowat least three teeth to be engaged in the thickness of material. INSTALLING THE BLADE with Keyless Quik-Change ™ Blade Clamp 1...

Page 10 - Periodically clean the blade clamp with dry compressed air.; DO NOT; lubricate the blade clamp. Lubricant can attract contamination.; INSTALLING THE OPTIONAL BLADE ADAPTER; DISCONNECT TOOL FROM POWER SOURCE.; INSTALLING; section of this manual.

10 If the blade breaks leaving nothing to grasp (to pull it from the clamp), it maybe necessary to use another blade as a tool to aid in removing the brokenpiece (see Fig. 5). While holding the release collar in the open position, usethe tip of another blade to “hook” the broken piece and pull it fr...

Page 11 - ROTATABLE GEAR HOUSING ADJUSTMENT; FRONT SCROLL HOUSING ADJUSTMENT

11 ROTATABLE GEAR HOUSING ADJUSTMENT DISCONNECT TOOL FROM POWER SOURCE. 1. The variable angle reciprocating saw is designed with a rotatable gearhousing for easy adjustment of cutting angle. This feature permits access toplaces where conventional tools cannot be used. 2. The gear housing can rotate ...

Page 12 - PIVOTING GUIDE SHOE ADJUSTMENT; with keyless

12 PIVOTING GUIDE SHOE ADJUSTMENT with keyless Quik-Change ™ DISCONNECT TOOL FROM POWER SOURCE. DO NOT OPERATE THE TIGER SAW ® WITH THE GUIDE SHOE REMOVED. The Model 750 is supplied with a keyless Quik-Change ™ guide shoe. The pivoting guide shoe (A) Fig. 10, serves as a rest while making a cut and ...

Page 13 - HOW TO HOLD SAW; . The rubber front housing

13 HOW TO HOLD SAW The metal parts of the saw, blade and pivoting guide shoe may be made liveif the blade cuts into live wiring within a wall. To prevent accidental electrical shock the tool must be held as shown in Fig. 13 or Fig.14, and have the rubber front housingcover properly installed and NOT...

Page 14 - TO START AND STOP SAW; on the specification plate on the saw. Connect saw to power circuit.; VARIABLE SPEED

14 TO START AND STOP SAW 1. Make sure swicth is off and power circuit voltage is the same as shown on the specification plate on the saw. Connect saw to power circuit. 2. Hold saw firmly (see Fig. 13 or Fig.14). Squeeze trigger switch (A) Fig. 15, to start motor. Release trigger to stop motor. VARIA...

Page 15 - PLUNGE CUTS; DO NOT ATTEMPT TO PLUNGE CUT METAL.; NOT; SAWING METAL

15 PLUNGE CUTS The variable angle reciprocating saw can be used for plunge cutting wood,plywood, wallboard, and plastic materials. DO NOT ATTEMPT TO PLUNGE CUT METAL. Clearly mark line of cut on the work. Grasp front housing with one hand andrear handle with the other hand. Choose a convenient start...

Page 16 - TROUBLESHOOTING; KEEP TOOL CLEAN; Wear ANSI Z87.1 safety glasses while using compressed air.; FAILURE TO START; DELTA FACTORY; MAINTENANCE

16 For assistance with your tool, visit our website at www.porter-cable.com for a list of service centers or call the Porter-Cable help line at 1-800-487-8665. TROUBLESHOOTING KEEP TOOL CLEAN Periodically blow out all air passages with dry compressed air. All plastic partsshould be cleaned with a so...

Page 17 - ACCESSORIES; REPLACEMENT PARTS; SERVICE

17 A complete line of accessories is available from your Porter-Cable • Delta Supplier, Porter-Cable • Delta Factory Service Centers, and Porter-Cable Authorized Service Stations. Please visit our Web Site www.porter-cable.com for a catalog or for the name of your nearest supplier. Since accessories...

Porter-Cable 750 - Manual

Table of Contents:

Summary

Other Porter-Cable Models