Porter-Cable 340 - Manual

Porter-Cable 340

Porter-Cable 340 – Manual, read for free online in PDF format. We hope this helps you resolve any issues you may have. If you have further questions, please contact us through the contact form.

1 Page 1
2 Page 2
3 Page 3
4 Page 4
5 Page 5
6 Page 6
7 Page 7
8 Page 8
9 Page 9
10 Page 10
11 Page 11
12 Page 12
13 Page 13
14 Page 14
15 Page 15
Page: / 15

Table of Contents:

  • Page 2 – GENERAL SAFETY RULES; WORK AREA
  • Page 4 – SPECIFIC SAFETY RULES AND SYMBOLS; Always disconnect; the sander cord plug from the power circuit before; Sanding of lead-based paint is not recommended.; should only be removed by a professional.; Some wood contains preservatives which can be toxic.; Take extra
  • Page 6 – MOTOR; Do not operate your tool on a current on which the; EXTENSION CORD SELECTION; FUNCTIONAL DESCRIPTION; FOREWORD; ASSEMBLY; PREPARATION FOR SANDING; SELECTING THE RIGHT ABRASIVE SHEET
  • Page 8 – PAPER PUNCH; DISCONNECT TOOL FROM POWER SOURCE.
  • Page 9 – OPERATION; TO START AND STOP SANDER; Make certain the switch is in the “OFF” position, and the; HOW TO HOLD SANDER
  • Page 10 – ACCESSORY PADS
  • Page 11 – USING THE SANDER; SANDING PROCEDURE
  • Page 12 – REMOVING PAINT AND VARNISH; Read and follow all instructions in the ADDITIONAL; CABINETS AND DOORS; MAINTENANCE; KEEP TOOL CLEAN; Wear safety glasses while using compressed air.; FAILURE TO START
  • Page 13 – SERVICE AND REPAIRS; D E L T A; ACCESSORIES; Delta Factory Service Centers, and; Since accessories other than those offered by
  • Page 14 – ONE YEAR WARRANTY
Loading the manual

Double Insulated
Finishing Sander

Instruction

manual

The Model and Serial No. plate is located on the main
housing of the tool. Record these numbers in the
spaces below and retain for future reference.

Model No. ______________________________________

Type ___________________________________________

Serial No. _______________________________________

IMPORTANT

Please make certain that the person who is
to use this equipment carefully reads and
u n d e r s t a n d s t h e s e i n s t r u c t i o n s b e f o r e
starting operations.

Part No. 900008 - 04-29-02

ESPAÑOL: PÁGINA 15
FRANÇAISE : PAGE 29

MODEL 340

To learn more about Porter-Cable

visit our website at:

http://www.porter-cable.com

Copyright © 2002 Porter-Cable Corporation

900008 - 04-29-02.qxd 5/23/02 2:17 PM Page 1

"Loading the manual" means you need to wait until the file loads and becomes available for online reading. Some manuals are very large, and the time they take to appear depends on your internet speed.

Summary

Page 2 - GENERAL SAFETY RULES; WORK AREA

2 WARNING: SOME DUST CREATED BY POWER SANDING, SAWING, GRINDING, DRILLING, AND OTHER CONSTRUCTION ACTIVITIES contains chemicals known to cause cancer, birth defects or otherreproductive harm. Some examples of these chemicals are:· lead from lead-based paints,· crystalline silica from bricks and ceme...

Page 4 - SPECIFIC SAFETY RULES AND SYMBOLS; Always disconnect; the sander cord plug from the power circuit before; Sanding of lead-based paint is not recommended.; should only be removed by a professional.; Some wood contains preservatives which can be toxic.; Take extra

4 SPECIFIC SAFETY RULES AND SYMBOLS 1. Always disconnect the sander cord plug from the power circuit before changing abrasive sheets. 2. Sanding of lead-based paint is not recommended. Lead-based paint should only be removed by a professional. 3. Some wood contains preservatives which can be toxic. ...

Page 6 - MOTOR; Do not operate your tool on a current on which the; EXTENSION CORD SELECTION; FUNCTIONAL DESCRIPTION; FOREWORD; ASSEMBLY; PREPARATION FOR SANDING; SELECTING THE RIGHT ABRASIVE SHEET

6 MOTOR Many Porter-Cable tools will operate on either D.C., or single phase 25 to 60cycle A.C. current and voltage within plus or minus 5 percent of that shownon the specification plate on the tool. Several models, however, are designedfor A.C. current only. Refer to the specification plate on your...

Other Porter-Cable Models